XRAY T3 ---- General Forum

duartev · **Posted:** Sun Dec 12, 2010 16:53:26

thanks, I will try to put them on excel and test it

Psycho_ · **Joined:** Fri Oct 01, 2010 18:35:36 **Posts:** 8

What about the new upper bulkead?

Mark Christopher · **Posted:** Tue Dec 28, 2010 13:39:20

[quote="Psycho_"][img]http://ets.redrc.net/wp-content/gallery/ets-1011-round-2-hrotovice-czech-republic/sat-dankelt3-4.jpg[/img]

What about the new upper bulkead?[/quote]

Got steel out drives and blades too.

Psycho_ · **Joined:** Fri Oct 01, 2010 18:35:36 **Posts:** 8

But, any release data for this new upper bulkhead?? We're waiting it!

Green Wing · **Posted:** Wed Jan 12, 2011 18:59:36

Hello.

- Are all the spare parts available in the "R" spec of the T3, too, or just a few?
- The supplementary sheet of the T3R says 4 silver and 4 golden springs. Is this correct or a printing error?
- And (sorry for that one) why are the composite outdrives of the ball diff at 97% of the price of the machined ones?

Edit: I just ask because I found 2 silver and 2 golden ones in the box.

Thanks,
Stefan

Skiddins · **Posted:** Thu Jan 13, 2011 02:54:40

Green Wing · **Posted:** Thu Jan 13, 2011 09:28:41

brano · **Posted:** Fri Jan 14, 2011 08:19:08

Green Wing · **Posted:** Fri Jan 14, 2011 13:19:20

Hello Brano,

where then is the sence in a "R" spec model? I mean I have not bought it because of its low price (and also don't have much wear so far) but just to try out ET and to have something real for the winter besides VRC. I like it and will buy a T3'11 in addition.
But for sure there are hobbyists who are thinking about buying a "R" model because of its price and they would do so because of lower maintenance costs (wished or needed).

If there's no interest in producing most of the "R" spec spare parts like other manufacturers do then at least it would be fair to not only say this in a supplementary sheet via pdf-file (you can't await that eveyone reads a supplementary sheet before buying a product) but primary point on this theme on top of the "R" model'(s)' page. My opinion.

brano · **Posted:** Mon Jan 17, 2011 09:00:59

If you check the supplementary sheet than you will find that just the glassfiber parts (chassis, top deck and shock towers) are not produced, instead of them XRAY offers the standard graphite parts. All other parts you can get (alu parts like bulkheads are offered just in orange color, not in silver).

Psycho_ · **Joined:** Fri Oct 01, 2010 18:35:36 **Posts:** 8

No comments about upper bulkhead? :shock:

Hagberg · **Posted:** Thu Jan 27, 2011 10:49:30

TC Racer · **Posted:** Wed Feb 02, 2011 21:20:57

Skiddins · **Posted:** Wed Feb 02, 2011 22:31:09

I used a combination of these parts;

XR302655 - BALL END 4.9MM WITH THREAD 10MM (2) (For the front C hubs)
XR302654 - BALL END 4.9MM WITH THREAD 8MM (2)
XR302653 - BALL END 4.9MM WITH THREAD 6MM (2)

XR302665 - COMPOSITE BALL JOINT 4.9MM - CLOSED WITH HOLE (4)

Jerryd · **Joined:** Fri Feb 04, 2011 01:28:49 **Posts:** 4

I recently purchased my 1st Touring car, an X-Ray T3 Rubber edition. I don't have a stock of spare parts so I'm looking for a little help.
I have a Futaba S-9551 Servo and would like to know what parts I need for a proper installation along with the proper layout of the linkage.
Everything I have tried causes the rod end to hit the top plate when it passes over center.
Any help on the setup would be appreciated.

Jerry...

Hagberg · **Posted:** Thu Feb 10, 2011 00:42:40

Jerryd · **Joined:** Fri Feb 04, 2011 01:28:49 **Posts:** 4

Hagberg · **Posted:** Tue Feb 15, 2011 23:57:13

indymodz · **Joined:** Fri Aug 06, 2010 03:20:52 **Posts:** 4

When/where can I get these bulkheads in the US??

Hurrle · **Posted:** Mon Mar 07, 2011 12:46:06

Don't think it is available yet. Haven't found it anywhere.

XRAY - Model racing cars

XRAY T3 ---- General Forum

Who is online