XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
DIFF O-RINGS ? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=8545 |
Page 1 of 2 |
Author: | Butcher [ Thu Dec 11, 2008 06:08:15 ] |
Post subject: | DIFF O-RINGS ? |
Author: | Robin Frischkopf [ Thu Dec 11, 2008 14:44:15 ] |
Post subject: | |
Do you put them in dry or lube them up with something? I use GMK shock snot to lube up the o-rings. They last longer and don't let oil out. http://www.gmksupply.com/html/gmk_0102_.html |
Author: | Jason Branham [ Thu Dec 11, 2008 20:40:58 ] |
Post subject: | |
Butcher, Like Robin said make sure you lube them with a grease and you should'nt see any leaking problems. The o-rings work like they are supposed to and shold'nt be leaking atleast I don't see that in my car. |
Author: | Bazza [ Thu Dec 11, 2008 22:12:20 ] |
Post subject: | |
Do you lube your shock shafts too? If not, then do so - I soak mine in the oil/fluid I am going to be using overnight, OK that be a bit ott but hey, when rebuilding I'll leave all seals and o rings to soak for as long as OFF TOPIC! I am not getting any indication to new posts, nothing is highlighting on the forum at all for me? ~ Anyone else getting this? |
Author: | Butcher [ Fri Dec 12, 2008 03:36:01 ] |
Post subject: | |
Author: | Steve Walters [ Fri Dec 12, 2008 03:49:20 ] |
Post subject: | |
Author: | Jorg van Leuken [ Fri Dec 12, 2008 08:02:15 ] |
Post subject: | |
Author: | daveg [ Fri Dec 12, 2008 11:48:34 ] |
Post subject: | |
is it possible that your diff casings have been bored out too deep where the o ring sits? is the crown gear side the same as the gear side? are all your diffs the same? dave |
Author: | Jason Branham [ Fri Dec 12, 2008 15:17:33 ] |
Post subject: | |
Jorg, Thoes are the correct ones so I don't understand the problem. I use the same and never have they given me a probelm. Have you contacted Xray or your distributor about this? I will see if I can get Mario on this. |
Author: | daz.fx [ Fri Dec 12, 2008 21:05:11 ] |
Post subject: | |
Author: | Bazza [ Sat Dec 13, 2008 01:46:00 ] |
Post subject: | |
Author: | Butcher [ Sat Dec 13, 2008 03:32:19 ] |
Post subject: | |
Author: | Butcher [ Sat Dec 13, 2008 03:57:11 ] |
Post subject: | |
Author: | daveg [ Sat Dec 13, 2008 13:35:35 ] |
Post subject: | |
Author: | brano [ Mon Dec 15, 2008 11:00:04 ] |
Post subject: | |
Author: | KaGe [ Mon Dec 15, 2008 11:20:18 ] |
Post subject: | |
Author: | Rocco Margiotta [ Mon Dec 15, 2008 15:19:57 ] |
Post subject: | |
Author: | daz.fx [ Mon Dec 15, 2008 19:45:19 ] |
Post subject: | |
Author: | Butcher [ Tue Dec 16, 2008 04:09:09 ] |
Post subject: | |
Author: | Ian2009 [ Sun Dec 28, 2008 03:06:58 ] |
Post subject: | Diff Cup O-Ring Bore Depth XT8 |
The depth of the internal o-ring bore on brand new cup is 1.91mm, & the bore diameter is 8.84mm using a digital vernier. |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |