Keyser-Soze
could you show us a picture of what sort of wear your getting ?
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| cvd pin removal https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=8375 |
Page 1 of 2 |
| Author: | daniel366940 [ Mon Oct 20, 2008 21:04:00 ] |
| Post subject: | cvd pin removal |
| Author: | daz.fx [ Mon Oct 20, 2008 22:04:43 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Mon Oct 20, 2008 22:58:33 ] |
| Post subject: | |
| Author: | Keyser-Soze [ Tue Oct 21, 2008 01:46:20 ] |
| Post subject: | |
| Author: | Butcher [ Tue Oct 21, 2008 02:42:25 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Tue Oct 21, 2008 04:33:34 ] |
| Post subject: | |
| Author: | Keyser-Soze [ Tue Oct 21, 2008 11:21:17 ] |
| Post subject: | |
| Author: | Oli [ Tue Oct 21, 2008 11:46:30 ] |
| Post subject: | |
| Author: | Tricksy [ Tue Oct 21, 2008 13:46:27 ] |
| Post subject: | |
Keyser-Soze could you show us a picture of what sort of wear your getting ?
|
|
| Author: | Keyser-Soze [ Tue Oct 21, 2008 13:59:09 ] |
| Post subject: | |
Yeah for sure,but i can only post it on the weekend,because my car is at home and i'm not! The play that i talk is between the dogbone and the cilinder! |
|
| Author: | Oli [ Tue Oct 21, 2008 15:08:32 ] |
| Post subject: | |
Just to clarify, the end of the drive shaft that goes into the diff outdrive? Or the end of the drive shaft that goes into the wheel axel? |
|
| Author: | daniel366940 [ Tue Oct 21, 2008 19:22:50 ] |
| Post subject: | |
the end of the centre drive shafts that go into the centre diff outdrives they have flats on them |
|
| Author: | Keyser-Soze [ Tue Oct 21, 2008 19:39:35 ] |
| Post subject: | |
I'm getting the play where the cilinder enters in the dog bone,in other words,i've got play between the cilinder and the dog bone! |
|
| Author: | Oli [ Tue Oct 21, 2008 22:05:16 ] |
| Post subject: | |
I wouldn't worry about a little bit of play between the drive shafts and diff out drives. Mine have got flats on them, but it doesn't have any effect on performance at all. Although you can feel a little play when you manually rotate the drive train, what it equates to in real terms is a millisecond delay between getting on power or braking. You would never notice it no matter how big the flat spots get. All you need to be concerned about is the pin wearing so thin it becomes weak. That said, I've seen a friends car that's been run pretty much every weekend since the 808 was released that still had life left in the pins! |
|
| Author: | Barkley Abernethy [ Tue Oct 21, 2008 22:08:55 ] |
| Post subject: | |
look at the tiny pin that goes through the cylinder ..if its marked which it prolly is replace it they are cheap for a pack of ten . your cdv end that goes through the hub has 4 holes in it so you can rotate it and use the other 2 holes this extends the life . if you do not grease these after every race meeting the wear rate will be quicker .. i grease mine and change the pins every 90 mins of run time ...... the cvd set up is far easier on the pocket than the universal.....i have over 20 meetings on my shafts with only pin replacements and it wouldnt have cost me 10 quid all year .......... |
|
| Author: | auto2 [ Wed Oct 22, 2008 00:15:04 ] |
| Post subject: | |
hey lotus? wouldnt putting greese there attract all sorts of dirt? |
|
| Author: | Rocco Margiotta [ Wed Oct 22, 2008 02:49:11 ] |
| Post subject: | |
For a joint like this you would probably want a wax based lubricant like a dirt bike or mountain bike chain lube. You will have to reapply it often but it will prolong the life of the joint. |
|
| Author: | wirtz88 [ Wed Oct 22, 2008 05:59:17 ] |
| Post subject: | |
Rocco I was put on to a product called 'dry ice' for bearings and gears. Petro solution with some sort of lubricant in it. The petro base de-greases the bearing and pushes dirt particles out, then evaporates and leaves a dry lubricant on the bearing, thus does not attract dust. It is working super good so far. You won't believe how much the bearing free's up after treatment. I local b-team xray driver showed it to me. He is still running the factory bearings after running nearly every weekend since the first release of the 808, so he is nearing 20 race weekends on his factory set of bearings. |
|
| Author: | Rocco Margiotta [ Wed Oct 22, 2008 20:29:35 ] |
| Post subject: | |
Oh wow, I'll have to try that out. Told me just in time, I've been needing to replace my center drive shafts. This stuff? |
|
| Author: | Barkley Abernethy [ Thu Oct 23, 2008 07:22:12 ] |
| Post subject: | |
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|