| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Massimo Fantini (Max Power)! https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=7710 |
Page 1 of 2 |
| Author: | Kahuna77 [ Thu May 22, 2008 03:45:14 ] |
| Post subject: | Massimo Fantini (Max Power)! |
Can't wait to run these two in, should be sweet mills. I'm going to throw the 5 port in the 808 and the 8 port in my XT8. Anyone have any experience with either of the two? |
|
| Author: | Steve Walters [ Thu May 22, 2008 04:03:30 ] |
| Post subject: | Re: Massimo Fantini (Max Power)! |
| Author: | Richmond [ Thu May 22, 2008 04:30:20 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Thu May 22, 2008 06:35:52 ] |
| Post subject: | |
| Author: | Leon McIntosh [ Thu May 22, 2008 07:04:09 ] |
| Post subject: | |
| Author: | Kahuna77 [ Thu May 22, 2008 07:46:39 ] |
| Post subject: | |
| Author: | sturla [ Thu May 22, 2008 09:01:40 ] |
| Post subject: | |
| Author: | Jason Branham [ Thu May 22, 2008 14:46:02 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Thu May 22, 2008 16:39:42 ] |
| Post subject: | |
| Author: | kilana [ Thu May 22, 2008 16:51:48 ] |
| Post subject: | |
| Author: | Richmond [ Thu May 22, 2008 16:56:50 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Thu May 22, 2008 17:01:47 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Thu May 22, 2008 17:03:31 ] |
| Post subject: | |
| Author: | Richmond [ Thu May 22, 2008 17:12:22 ] |
| Post subject: | |
| Author: | Jason Branham [ Thu May 22, 2008 17:15:06 ] |
| Post subject: | |
| Author: | Keith [ Thu May 22, 2008 17:21:28 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Thu May 22, 2008 18:10:02 ] |
| Post subject: | |
| Author: | gtsum [ Fri May 23, 2008 03:25:33 ] |
| Post subject: | |
I ran a Max Power M5 and it was great...at 5 gallons I still could not turn it over by hand (dropped plug wire hammered it though:(). The most power I got was the 1005 pipe with long header (I would get a low end bog with a short header with that pipe). As mentioned 9886 pipe with long header works well, as does the 9853 (which is what I ran most of the time). I averaged about 8-9 minutes per tank. It was my favorite motor I have ran...very smooth, linear, and fast...with the 1005 pipe on there there was not a motor in another truggy that could pull it down a long (150 ft) straight. I will say that I feel my GRP tuned 21 seems to have a bit more power (all throughout) and longer runtimes then my M5 had, but I would not hesitate to pick up another M5 if available |
|
| Author: | Keith [ Fri May 23, 2008 17:53:25 ] |
| Post subject: | |
| Author: | sturla [ Sat May 24, 2008 21:39:07 ] |
| Post subject: | |
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|