Rocco aren't you suppose to know everything??
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| 808 optional engine mount https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=7663 |
Page 1 of 2 |
| Author: | Keith [ Mon May 12, 2008 19:57:20 ] |
| Post subject: | 808 optional engine mount |
http://www.teamxray.com/teamxray/news/n ... on%20Parts |
|
| Author: | HulkRay [ Mon May 12, 2008 21:15:19 ] |
| Post subject: | |
When will they will be out? Guys I was breakin my engine this weekend and I took the engine off and on a lot of times and the mesh still kept well. I took the engine off by the engine screws not the mount screws so I did not had to reset the mesh at all.. What would be the advantage of these mounts other than it looks really nice... THanks Felix |
|
| Author: | Rocco Margiotta [ Mon May 12, 2008 21:52:59 ] |
| Post subject: | |
You have a straight shot at the screws that secure the mount, so you don't have to risk your ball end wrench or remove the head of the motor. |
|
| Author: | Robin Frischkopf [ Mon May 12, 2008 21:57:07 ] |
| Post subject: | |
Also as there's no aligning pin the mesh can still be way off if the engine moves a bit when you reinstall it. And without removing the head you can't put enough pressure on the screw. I've seen some lost engine screws these past few weeks and it was always because of this. |
|
| Author: | HulkRay [ Mon May 12, 2008 21:58:17 ] |
| Post subject: | |
ok when are they shipping or the shops already have them. Also which will be good for my GO Tech Engine .21.. |
|
| Author: | Rocco Margiotta [ Mon May 12, 2008 22:21:44 ] |
| Post subject: | |
Hopefully they're shipping within this week, but I won't know for sure until later on this week. As far as the GO tech engine goes, I am not sure.... Sorry! |
|
| Author: | HulkRay [ Mon May 12, 2008 22:35:11 ] |
| Post subject: | |
Rocco aren't you suppose to know everything??
|
|
| Author: | Barkley Abernethy [ Tue May 13, 2008 00:23:18 ] |
| Post subject: | |
os mount for a go get em |
|
| Author: | Rocco Margiotta [ Tue May 13, 2008 00:36:41 ] |
| Post subject: | |
| Author: | Tank time [ Tue May 13, 2008 01:37:56 ] |
| Post subject: | |
| Author: | Raymond Norte [ Tue May 13, 2008 03:05:34 ] |
| Post subject: | |
| Author: | HulkRay [ Tue May 13, 2008 03:25:41 ] |
| Post subject: | |
| Author: | gtsum [ Tue May 13, 2008 05:01:27 ] |
| Post subject: | |
| Author: | Keith [ Tue May 13, 2008 17:16:21 ] |
| Post subject: | |
| Author: | dbarnes [ Tue May 13, 2008 19:22:17 ] |
| Post subject: | |
| Author: | Keith [ Tue May 13, 2008 21:35:23 ] |
| Post subject: | |
| Author: | zieluch [ Wed May 14, 2008 22:55:33 ] |
| Post subject: | |
I thing this pins holder are worser then the standart ones. I prefer made from alu but for standard pins. |
|
| Author: | skidmark77 [ Wed May 14, 2008 23:17:25 ] |
| Post subject: | |
I use regular lock washers on the engine and mount with no issues. http://www.tonysscrews.com/product.sc?c ... oductId=98 |
|
| Author: | Oli [ Mon May 19, 2008 16:30:39 ] |
| Post subject: | |
| Author: | Rocco Margiotta [ Mon May 19, 2008 17:04:19 ] |
| Post subject: | |
I'm not sure about your 'neck of the woods' but they are on the way to us, so check with the UK distributor to make sure. |
|
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|