| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Whats wrong with my engine? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=7642 |
Page 1 of 1 |
| Author: | B Revis [ Thu May 08, 2008 04:47:35 ] |
| Post subject: | Whats wrong with my engine? |
Im trying to install the flywheel on to my engine but when i snugg it down it dont want to turn over smooth anymore.Im only snugging it allittle. |
|
| Author: | whitey4311 [ Thu May 08, 2008 06:26:22 ] |
| Post subject: | |
Is the brass collet touching the front bearing? It should only touch the inner race of the bearing and nothing else. When you say it wont turn over are you saying you cant cycle the piston to TDC by hand turning the flywheel? Try and explain this a bit more and I bet we can help. |
|
| Author: | B Revis [ Thu May 08, 2008 12:06:52 ] |
| Post subject: | |
| Author: | whitey4311 [ Thu May 08, 2008 17:54:49 ] |
| Post subject: | |
| Author: | Keith [ Thu May 08, 2008 18:58:43 ] |
| Post subject: | |
| Author: | DaleJrRocks8 [ Thu May 08, 2008 22:24:51 ] |
| Post subject: | |
| Author: | B Revis [ Fri May 09, 2008 01:47:35 ] |
| Post subject: | |
Im not turning the motor all the way over it is a brand new novarossi p5xs.What im talking about is the crank turns smooth without the flywheel im talking down around bdc ya know just like a half turn or so but when I put the flywheel on, it dont turn as free as it was before still down around bdc like the flywheel is to tight.Also its not touching the front of the engine. |
|
| Author: | daz.fx [ Fri May 09, 2008 02:54:03 ] |
| Post subject: | |
you must have shims touching the front bearing seal. This seal does not rotate like wheel bearings do. |
|
| Author: | Keith [ Fri May 09, 2008 20:09:47 ] |
| Post subject: | |
| Author: | Mader [ Sun May 11, 2008 20:44:54 ] |
| Post subject: | |
Seen this happen on O.S. Speed engine's. Rear bearing not quite seated all the way from factory. When the flywheel nut is tightened it binds the bearing a little. not saying thats what it is but if its new and you checked all the other typical things you might want to check! |
|
| Author: | Keith [ Mon May 12, 2008 01:33:17 ] |
| Post subject: | |
| Author: | B Revis [ Mon May 12, 2008 12:02:31 ] |
| Post subject: | |
[quote="Mader"]Seen this happen on O.S. Speed engine's. Rear bearing not quite seated all the way from factory. When the flywheel nut is tightenedTfor the reply thats what I think its doing im gonna break it down and check. |
|
| Author: | Stanley Wangsanegara [ Tue May 13, 2008 06:25:04 ] |
| Post subject: | |
| Author: | B Revis [ Wed May 14, 2008 01:52:34 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|