| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Well there we go the new XB8 https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=6968 |
Page 1 of 3 |
| Author: | whitey4311 [ Tue Jan 22, 2008 02:15:41 ] |
| Post subject: | Well there we go the new XB8 |
| Author: | gtsum [ Tue Jan 22, 2008 02:47:06 ] |
| Post subject: | |
| Author: | whitey4311 [ Tue Jan 22, 2008 03:35:03 ] |
| Post subject: | |
| Author: | Richmond [ Tue Jan 22, 2008 04:03:33 ] |
| Post subject: | |
| Author: | whitey4311 [ Tue Jan 22, 2008 04:17:18 ] |
| Post subject: | |
| Author: | MikeIz [ Tue Jan 22, 2008 04:34:38 ] |
| Post subject: | |
| Author: | low10s [ Tue Jan 22, 2008 04:36:45 ] |
| Post subject: | |
| Author: | whitey4311 [ Tue Jan 22, 2008 05:03:56 ] |
| Post subject: | |
| Author: | Robin Frischkopf [ Tue Jan 22, 2008 16:41:56 ] |
| Post subject: | |
| Author: | winkje [ Tue Jan 22, 2008 19:28:06 ] |
| Post subject: | |
Hi, Similar to the 'formal' EC announcement, I feel it bit sad..... sad that I do own 2 TQ's which are in perfect shape and drive awesome, but both are not the newest cars.... After 1 minute I start smiling that I'm lucky to drive two fantastic TQ's of which info is easily found as there's so much written already.... I like improvements and yes, I do think that this new car will be an improved one over the previous models. However, I still highle appriciate the quality of all XB8 versions and enjoy riding them... So, I will still buy spare parts if necessary (not really...) to enjoy my TQ's... Regards, vincent |
|
| Author: | Bren Ralls [ Tue Jan 22, 2008 20:07:13 ] |
| Post subject: | |
In the pictures & script relating to the prototype car You will see lots of little tweeks & prototype ideas, these as juraj needs to know how it affects things before he works his magic, but this he also wrote in the script. The bridge less arms you have been asking about, have been on test for quite a while now & I personally have used them since mid 07. Basics of them they are slightly shorter in length so longer pivot plates are used to keep car to width. Webbing is removed to allow them to flex like the long soft wishbones but they retain their shape because they are thicker & so do not warp. On the hub end a threaded shaft is used for strength. Bren |
|
| Author: | Richmond [ Tue Jan 22, 2008 21:18:18 ] |
| Post subject: | |
I just hope they do a conversion kit just like the EC Conversion kit. That was really a good way to hold onto the TQ owners who just bought the TQ. |
|
| Author: | kaan [ Tue Jan 22, 2008 22:25:58 ] |
| Post subject: | |
| Author: | Richmond [ Wed Jan 23, 2008 00:36:04 ] |
| Post subject: | |
| Author: | low10s [ Wed Jan 23, 2008 08:20:43 ] |
| Post subject: | |
| Author: | 180 booker [ Wed Jan 23, 2008 15:34:13 ] |
| Post subject: | |
| Author: | Richmond [ Thu Jan 24, 2008 01:25:58 ] |
| Post subject: | |
| Author: | Robin Frischkopf [ Thu Jan 24, 2008 14:59:40 ] |
| Post subject: | |
As far as I understand they are softer but won't warp like the old soft wishbones. |
|
| Author: | Richmond [ Thu Jan 24, 2008 17:38:04 ] |
| Post subject: | |
Will it work on the truggy? |
|
| Author: | Robin Frischkopf [ Thu Jan 24, 2008 18:57:25 ] |
| Post subject: | |
I guess you can just cut off the bridge. Problem is then at the slightest crash you might pop the outer hinge pin out, so that would have to be changed to a hinge pin with nuts or clips. |
|
| Page 1 of 3 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|