XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Suggest to XRAY which XB8 / XT8 Option Parts you wish? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=600 |
Page 1 of 34 |
Author: | mario [ Fri Dec 10, 2004 17:16:56 ] |
Post subject: | Suggest to XRAY which XB8 / XT8 Option Parts you wish? |
Author: | Neo-Buggy Phil [ Fri Dec 10, 2004 18:00:28 ] |
Post subject: | |
Author: | KenPro [ Fri Dec 10, 2004 19:12:17 ] |
Post subject: | |
Author: | motoazure [ Fri Dec 10, 2004 19:24:47 ] |
Post subject: | |
Author: | Booyah [ Fri Dec 10, 2004 20:39:46 ] |
Post subject: | |
Author: | BuLLdoGG [ Fri Dec 10, 2004 21:39:09 ] |
Post subject: | |
Author: | Booyah [ Fri Dec 10, 2004 22:20:46 ] |
Post subject: | |
Author: | z-man [ Fri Dec 10, 2004 22:49:52 ] |
Post subject: | |
Author: | Booyah [ Fri Dec 10, 2004 23:03:59 ] |
Post subject: | |
Author: | ChrisP [ Fri Dec 10, 2004 23:36:51 ] |
Post subject: | |
Author: | IPC [ Sat Dec 11, 2004 00:10:00 ] |
Post subject: | |
Author: | Hyper [ Sat Dec 11, 2004 01:16:59 ] |
Post subject: | |
-Pink fuel tank... -new body -x-ray xb8 nitro engine? |
Author: | SMRT [ Sat Dec 11, 2004 02:42:37 ] |
Post subject: | |
1. One Piece engine mount ![]() 2. revised front arms or c-hubs for more downtravel 3. front brace like the rear one 4. Stronger eccentric bushings 5. 1.1 clutch springs 6. Alu servo tray and alu mounts in no specific order ![]() |
Author: | pbfoot [ Sat Dec 11, 2004 03:29:37 ] |
Post subject: | |
1. aluminum front brace 2. steel eccentric bushings 3. 1 pc. engine mount 4. aluminum front steering top plate (the CF one) 5. aluminum front c hubs 6. aluminum rear hubs 7. titanium screws 8. aluminum center diff mount 9. aluminum center diff brace 10. titanium tie rods (all around) all in no specific order |
Author: | Troy Weatherholt [ Sat Dec 11, 2004 04:49:46 ] |
Post subject: | |
KenPro You mentioned wanting softer/harder anti-roll bars. Here is a list of the available bars. Front 352422 - 2.2 mm 352424 - 2.4 mm 352426 - 2.6 mm 352428 - 2.8 mm 352430 - 3.0 mm 352432 - 3.2 mm Rear 353424 - 2.4 mm 353426 - 2.6 mm 353428 - 2.8 mm 353430 - 3.0 mm 353432 - 3.2 mm And I am all for stronger upper ti-rods |
Author: | PaulBronca [ Sat Dec 11, 2004 05:46:13 ] |
Post subject: | |
Author: | showtime [ Sat Dec 11, 2004 10:53:03 ] |
Post subject: | |
Author: | Diesel Racer [ Sat Dec 11, 2004 11:05:25 ] |
Post subject: | |
Author: | jontejsson [ Sat Dec 11, 2004 12:12:36 ] |
Post subject: | |
Author: | Mikeobello [ Sat Dec 11, 2004 17:44:01 ] |
Post subject: | |
Page 1 of 34 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |