no one had this problem then???
need help guys
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Steering preload setting https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=4751 |
Page 1 of 1 |
| Author: | Big_Mac [ Sat Dec 30, 2006 15:02:30 ] |
| Post subject: | Steering preload setting |
I have a question about the steering pre-load setting for the servo saver, in my manual it is advised to set a gap of 2 mm, when i hold my wheels and turn the steering with the transmitter the servo can easaly push through the springtension left and right, is this a good setting or are you guys setting more pre-load. I use a Sanwa ERG-VX servo with a lot of torque. |
|
| Author: | what_stanger? [ Sat Dec 30, 2006 22:59:26 ] |
| Post subject: | |
how old is your manual? is the kit a xb8 TQ? or R? mine is a TQ, and I think it calls for a 1mm setting. It seemed a bit small and I set it for 1.5 I'll check a bit later. |
|
| Author: | Big_Mac [ Sun Dec 31, 2006 00:32:47 ] |
| Post subject: | |
It is a R kit that i bought about a year ago. I also noticed that in the manual for the TQ that i downloaded it says to make the gap 2 mm. |
|
| Author: | what_stanger? [ Sun Dec 31, 2006 02:20:15 ] |
| Post subject: | |
I have the actual manual for the TQ, and it says initial preload is 1.0mm. I just bought the kit a week ago, so I'm guessing its pretty new. Maybe they're putting a stronger spring in the newer kits??? I'll post a picture, if I can find the add attachments option... EDIT:picture taken from the XB8 manual I downloaded a little while back: |
|
| Author: | Big_Mac [ Sun Dec 31, 2006 11:43:36 ] |
| Post subject: | |
Well that's probably what it should be then according to XRAY, it says initial setting so i'm wondering if there are users who change this setting. I can imagine when entering a corner hard a stiffer setting will increase steering into the corner when you have sufficient servo torque. |
|
| Author: | Dotan Halevy [ Sun Dec 31, 2006 12:46:02 ] |
| Post subject: | |
i have erg-vx also, and my spring is set to 9 mm preload (almost locked). the steering have great response, and nothing breaks even at the hardest crashes. |
|
| Author: | Psygho [ Sun Dec 31, 2006 13:15:47 ] |
| Post subject: | |
I have an 13 kilo torque servo, and i have set it so thad the holding power of the servo is eneugh to push the wheelt trough the servo saver manualy. Moving power, wil just, put it trough just nearly either, but with great effort. |
|
| Author: | Big_Mac [ Sun Dec 31, 2006 18:02:26 ] |
| Post subject: | |
Dotan: That is a big risk for my new (expensive) servo but i can imagine that is will give a lot of steer. Psygho: I'm not quit sure about what you do setting yours, do you mean that you apply pressure to the wheels when the servo is under power and the transmitter is on and you push the wheel until the servo holding power gives? |
|
| Author: | Dotan Halevy [ Sun Dec 31, 2006 21:56:56 ] |
| Post subject: | |
[quote="Big_Mac"]Dotan: That is a big risk for my new (expensive) servo but i can imagine that is will give a lot of steer. quote] first of all, that servo is very strong, a lot more that you can think. in friend's mugen the servo horn broke and servo survived after a really big crash. the best servo i ever owned. second, the servo saver preload doesn't effects steering that much. it's affects more on steering response and keeping the wheels at the disired direction when driving over bumps. |
|
| Author: | Big_Mac [ Sun Dec 31, 2006 22:25:44 ] |
| Post subject: | |
I already heard that the servo was greatly appreciated by racers how also say it last a very long while, it is good to hear that you also have good results with the servo. I will try a view different tensions the next race that i will participate in, and see how it hold up. |
|
| Author: | Psygho [ Mon Jan 01, 2007 19:46:13 ] |
| Post subject: | |
| Author: | Big_Mac [ Mon Jan 01, 2007 21:34:24 ] |
| Post subject: | |
| Author: | Xb8 Boy [ Wed Feb 28, 2007 13:26:54 ] |
| Post subject: | |
hi guys, i rebuilt my xb8 a while ago and cleaned all the steering set up aswell. now i have a problem with the setting of around 1mm is moving on the spring. i did use blue thread-lock on it after it happened but its still doing it (im loosing the compression on the spring) the oring is still seated in there, so whats the prob? any ideas cheers |
|
| Author: | Xb8 Boy [ Sun Mar 04, 2007 15:49:50 ] |
| Post subject: | |
no one had this problem then???
need help guys |
|
| Author: | what_stanger? [ Tue Mar 06, 2007 00:46:52 ] |
| Post subject: | |
| Author: | Xb8 Boy [ Tue Mar 06, 2007 01:23:19 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|