XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
TQ upgrade kit https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=3481 |
Page 1 of 1 |
Author: | Wachsmann [ Mon Apr 24, 2006 23:29:45 ] |
Post subject: | TQ upgrade kit |
Author: | mario [ Wed Apr 26, 2006 21:26:31 ] |
Post subject: | |
Author: | JohnB [ Thu Apr 27, 2006 20:40:26 ] |
Post subject: | |
The new suspension holders are just a bit offset to accomodate the longer suspension pins and allow the option of adding clips to move the suspension arm position. The difference in the TQ arms and the stock XB8 arms are about half a mm at the mounting point. If you wanted to put TQ arms on your XB8 they will fit - you just might want to add a small shim to take up any slack. |
Author: | Barkley Abernethy [ Fri Apr 28, 2006 20:57:56 ] |
Post subject: | |
Author: | guy02 [ Fri Apr 28, 2006 23:24:35 ] |
Post subject: | |
Author: | JohnB [ Sat Apr 29, 2006 00:53:53 ] |
Post subject: | |
Author: | Barkley Abernethy [ Mon May 01, 2006 21:09:39 ] |
Post subject: | |
Author: | Rocco Margiotta [ Tue May 02, 2006 00:50:38 ] |
Post subject: | |
Author: | Richmond [ Tue May 02, 2006 13:34:23 ] |
Post subject: | |
Hey Rocco, any word on the new Max Power motors yet? |
Author: | Rocco Margiotta [ Tue May 02, 2006 18:27:52 ] |
Post subject: | |
Author: | twigstoy [ Thu May 04, 2006 14:35:53 ] |
Post subject: | |
Could someone please post the part numbers that is needed to upgrade to the TQ kit. Mine is just the regular XB8. Thanks |
Author: | Rocco Margiotta [ Thu May 04, 2006 21:16:41 ] |
Post subject: | |
This should be EVERY part on the car. 35 2112 - TQ front arm 35 1345 - Aluminum front upper plate 35 4055 - Aluminum center diff plate 35 6115 - Aluminum radio try 35 5061 - Extended front diff outdrives 35 2651 - Spring steel ball stud with backstop 35 2301 - Front TQ suspension 35 3301 - Rear TQ Suspension 35 3112 - TQ Right Rear arm 35 3122 - TQ Left rear arm 35 9050 - Clutch bearings 35 2096 - Aluminum Front brace 35 2089 - Composite Front brace 35 3089 - Composite Rear brace |
Author: | ajoiner490 [ Thu May 04, 2006 21:19:52 ] |
Post subject: | |
Oooh clutch bearings ![]() Off to South RC Pro series race Round 1! -Adam |
Author: | Rocco Margiotta [ Thu May 04, 2006 21:21:14 ] |
Post subject: | |
Mr. Burch and I should be leaving tonight around 10:30ish... See ye there, pal. Also, you know if I didn't say that some wise guy out there would be all over it, haha... |
Author: | Grim4g63t [ Thu May 04, 2006 21:30:42 ] |
Post subject: | |
good info to have, but thinking of just getting the TQ anyways, and good luck to you guys, and bring back pictures! ![]() |
Author: | Barkley Abernethy [ Mon May 15, 2006 18:36:33 ] |
Post subject: | |
Author: | Rocco Margiotta [ Mon May 15, 2006 21:08:14 ] |
Post subject: | |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |