Thx for all. Now i know with engine buy thx giorgi
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| With Sirio to xb8r https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=2069 |
Page 1 of 1 |
| Author: | zieluch [ Mon Aug 08, 2005 19:37:14 ] |
| Post subject: | With Sirio to xb8r |
I have sirio kanai 2 and i drive only 2 liter runner time top 25 and conecting rod was broked. I brake in this engine abaut 1.9 liters fuel. And now is my quastion with enging now buy sirio kanai 1 or 2 ?? |
|
| Author: | Gap Man [ Mon Aug 08, 2005 20:06:24 ] |
| Post subject: | |
RB WS7 II in my opinion...I run RB's across the board - 1/10th touring, 1/8th circuit and 1/8th off road - always found them ultra reliable and very competitive....not denegrating other brands though as have not tried many of them.... |
|
| Author: | zieluch [ Mon Aug 08, 2005 20:22:31 ] |
| Post subject: | |
I dont like RB. Some off my friend have RB and he fast sell ws7 2. ow i buy only sirioand what do you thing with are better k1 or 2 |
|
| Author: | casper7 [ Mon Aug 08, 2005 21:26:32 ] |
| Post subject: | |
| Author: | zieluch [ Mon Aug 08, 2005 21:54:48 ] |
| Post subject: | |
| Author: | casper7 [ Mon Aug 08, 2005 22:32:41 ] |
| Post subject: | |
| Author: | Giorgi50 [ Tue Aug 09, 2005 00:56:36 ] |
| Post subject: | |
The Sirio Kanai 1 and Kanai 2 are just about Identical. The only difference is the seal on the carb and case and the the ports have been fine tuned. Otherwise there the same engine. I would have to say the Kanai 2 is better becuase the carbs dont leak at the seal. The Kanai ones had a bad problem with air leaks at the base of the carb becuase of only having 1 seal. Now the engine has 2 seals. Hope that helps. Otherwise its a good engine, maybe it was a problem with the way you broke it in why the rod broke ? just a possiblity. I ran one last year and there quite powerful, they just dont last long, kinda like the O.S. engine. |
|
| Author: | auto2 [ Tue Aug 09, 2005 02:09:00 ] |
| Post subject: | |
my solution to long rod life is to always preheat the engine to at least 180 degrees as long as it has any pinch cold. it takes a long time to break it in but youll love the results. |
|
| Author: | zieluch [ Tue Aug 09, 2005 12:14:24 ] |
| Post subject: | |
Thx for all. Now i know with engine buy thx giorgi
|
|
| Author: | Ger [ Wed Aug 10, 2005 22:39:21 ] |
| Post subject: | |
| Author: | zieluch [ Wed Aug 10, 2005 23:07:41 ] |
| Post subject: | |
| Author: | Team X-Ray NZ [ Mon Aug 22, 2005 08:30:20 ] |
| Post subject: | |
| Author: | guy02 [ Mon Aug 22, 2005 10:04:15 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|