XB8 ---Buggy General Forum---

dgrobe2112 · **Posted:** Wed Mar 05, 2014 04:33:57

All the xb9e parts work.. u can cut down the left side guard.

ykc · **Joined:** Wed Feb 19, 2014 04:20:56 **Posts:** 11

dgrobe2112 · **Posted:** Wed Mar 05, 2014 05:50:21

No problem. Let me know if u need anything else.

Corde89 · **Posted:** Sat Mar 08, 2014 13:25:48

Good morning to all, i will ask: Do you know if arrive the XB8 elettric model?
Thank you
Andrea

dgrobe2112 · **Posted:** Sat Mar 08, 2014 22:57:08

It will be a while. I wish Xray would release a conversion. But they don't. All my xb9e stuff works on the xb8

vdsracing · **Posted:** Sun Mar 09, 2014 21:59:57

What is the best way to clean-maintain the front upper ball of the suspension.?

dgrobe2112 · **Posted:** Mon Mar 10, 2014 18:44:59

i would use air compressor.. to remove any dirt.. and the manual says to use small amount of WD40 on the pillow balls.

vis · **Posted:** Tue Mar 18, 2014 14:58:02

Please tell me which of these components fit FX engine:
358718 or 358719?

brano · **Posted:** Thu Mar 20, 2014 06:43:44

358718

vis · **Posted:** Fri Mar 21, 2014 08:02:51

vis · **Posted:** Mon Apr 21, 2014 14:57:10

Prompt please, why do we need Aluminum Shock Cap Nut w / Vent Hole (358054).
That can be adjusted via the vent hole?

Thanks in advance!

vis · **Posted:** Mon Apr 28, 2014 17:08:41

Robin Frischkopf · **Posted:** Mon Apr 28, 2014 17:39:04

As far as I know those are if you prefer to run with foam under your bladder and not with air pressure, this gives less/different rebound, and if you can't drill some holes into the caps yourself.

vis · **Posted:** Tue Apr 29, 2014 13:23:48

Robin Frischkopf · **Posted:** Wed Apr 30, 2014 19:07:56

I didn't know these new caps had screws so I don't know, sorry. I just know some drivers used to drill holes in their caps to work with foam. In the past few years I've used foam too but without holes.

vis · **Posted:** Wed May 07, 2014 09:06:38

baron · **Joined:** Sun Jan 25, 2015 14:34:32 **Posts:** 1

hi wonderiing if the new 2015 composit material is stronger on the front upper suspension inner arms as it seems to be the week point of the front end

djb · **Joined:** Thu Apr 23, 2015 08:33:47 **Posts:** 2

Does anyone going to answer my questions and help me with that please? I'm going to hit the track on saturday with my XB8 2015.

1. Do we have some combinations working together for the rear camber link (shock tower - rear hub)? Or can mess up everything? And also what length i must do for the camber? to have 3 degrees? I don't have a setup port.

2. Some questions here about shock absorbers setup. Anyone having the experience on that ?
a. When to use different shock piston, e.g 6 hole or 10 hole that we have in the kit ?
b. What is the effect of piston hole size?
c. When to use flat piston? Why we don't use flat pistons ?
d. What is the correct way of shocks setup? Choose piston and spring and then adjust for the oil or what?

3. What will be the effect of the spacers on front upper arms? What can achieve by moving the arm forward and backwards?

dgrobe2112 · **Posted:** Thu Apr 23, 2015 15:24:16

XRAY - Model racing cars

XB8 ---Buggy General Forum---

Who is online