XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
XB8 setup----VERY bumpy/rough track https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=1624 |
Page 1 of 2 |
Author: | Booyah [ Mon May 16, 2005 17:57:41 ] |
Post subject: | XB8 setup----VERY bumpy/rough track |
Author: | slim [ Mon May 16, 2005 18:09:45 ] |
Post subject: | |
Author: | FreakOfNature [ Mon May 16, 2005 18:37:17 ] |
Post subject: | |
Author: | djray77 [ Mon May 16, 2005 19:41:38 ] |
Post subject: | |
Author: | Booyah [ Mon May 16, 2005 20:42:42 ] |
Post subject: | |
Author: | sturla [ Mon May 16, 2005 20:43:07 ] |
Post subject: | |
Author: | nolec5 [ Mon May 16, 2005 21:13:21 ] |
Post subject: | |
Author: | team lobo [ Mon May 16, 2005 22:08:15 ] |
Post subject: | |
Author: | Booyah [ Mon May 16, 2005 22:28:49 ] |
Post subject: | |
Author: | BaldyB [ Mon May 16, 2005 22:32:09 ] |
Post subject: | |
Author: | Booyah [ Mon May 16, 2005 22:36:52 ] |
Post subject: | |
Author: | team lobo [ Mon May 16, 2005 22:44:06 ] |
Post subject: | |
Author: | Giorgi50 [ Mon May 16, 2005 23:32:48 ] |
Post subject: | |
Author: | Rich Panganiban [ Tue May 17, 2005 00:27:50 ] |
Post subject: | |
Author: | Booyah [ Tue May 17, 2005 18:43:37 ] |
Post subject: | |
Author: | jontejsson [ Tue May 17, 2005 19:11:23 ] |
Post subject: | |
I have kind of the same problem, the car handles quite well on smooth sections like the straight but it lacks it is bad on the rough parts. Would softer springs/a-arms help to make it handle the rough parts better? I have the soft light blues with 350W both front and rear. |
Author: | gustavsen [ Tue May 17, 2005 20:51:35 ] |
Post subject: | |
Author: | Booyah [ Thu May 19, 2005 10:28:16 ] |
Post subject: | |
Think I may change my springs to the stock blues for the next time out with a little preload and see how that does. I have never ran them yet |
Author: | Mike Dana [ Thu May 19, 2005 18:23:43 ] |
Post subject: | |
Sorry, I don't get in here as much as I should! Hopefully, things will mellow out a bit and I can get back on these boards more frequently. If you go to the downloads section and pull my set-up from "Spring Shoot-out" I think you will like it. It was a soft dirt, VERY rough track and the set-up was really, really good. For the 3-hole pistons, get a 1.5mm bit. Redrill 2, 1.4 straight hole pistons and add a 3rd hole somwhere in the middle (between) the 2 standard holes. Make sure you drill the 3rd hole staight and not at an angle etc. Hope this helps, Mike |
Author: | guy02 [ Thu May 19, 2005 18:33:54 ] |
Post subject: | |
Mike I want to try 4x 1.4 or 1.3 holes I think that could work great |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |