XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
XB9 servo saver on 808 https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=13434 |
Page 1 of 1 |
Author: | Garakis(Greece) [ Wed Mar 13, 2013 15:28:45 ] | ||||
Post subject: | XB9 servo saver on 808 | ||||
Hey everybody,this is my first patent and i want some opinions & advices.You can see photos .Because i don't like this weight(see photos) i want to know if xb9's servo saver(#352512) fits on 808 These 2 plastics.The steering is the same as before I AM WAITING ANSWERS AND OPINIONS!!!!!
|
Author: | Robin Frischkopf [ Wed Mar 13, 2013 15:39:19 ] |
Post subject: | Re: XB9 servo saver on 808 |
I don't see why it would not fit and the plastic parts don't cost the world so just try it. |
Author: | Garakis(Greece) [ Wed Mar 13, 2013 17:10:34 ] |
Post subject: | Re: XB9 servo saver on 808 |
I saw xb9's manual and 808's manual and:The bearings are the same,the spring under these plastics are the same.One question if i cut down the carbon fiber so the servo goes more down will i lose flex? |
Author: | Robin Frischkopf [ Sun Mar 17, 2013 19:15:18 ] |
Post subject: | Re: XB9 servo saver on 808 |
When you put on the XB9 servo saver plastic parts I'm pretty sure the whole linkage will be raised up and you don't have to cut anything. |
Author: | Garakis(Greece) [ Mon Mar 18, 2013 20:27:13 ] |
Post subject: | Re: XB9 servo saver on 808 |
Thanks a lot my friend..Here is a video: http://www.youtube.com/watch?v=HLjPk1XDqhw |
Author: | dgrobe2112 [ Wed Mar 27, 2013 21:09:04 ] |
Post subject: | Re: XB9 servo saver on 808 |
i am confused as to what i am seeing. what is all those spacers for? |
Author: | Garakis(Greece) [ Fri Mar 29, 2013 16:12:55 ] |
Post subject: | Re: XB9 servo saver on 808 |
Which spares do you mean?If you mean the washers & nuts,i put them to get the link higher. Also i ordered the xb9's composite servo saver and when i willl have it i will post again here to show you the results.But i am very positive about this patent. |
Author: | Green Wing [ Wed Apr 03, 2013 16:49:16 ] |
Post subject: | Re: XB9 servo saver on 808 |
At the moment I'm finishing a TIX TX9 based on XT8'09 and XB9 normally. But I use my "old" 808'09'11 parts and for what I can see it's just another height in the servo saver's lever and a different Ackermann rail (same mounting, different positions). If you would use the XB9 composites, you could get rid of the shims and therefor you get a more direct feel on the steering. As for the change in flex by reducing the radio plate's height, theoretically the flex will increase just for a very little bit but there's still the front brace so no worry about that. I didn't notice that when I removed 1.5mm on top and bottom of the steering servo mounts and 3mm on the radio box to make the same servos you have fit. Nice built! |
Author: | Garakis(Greece) [ Tue Apr 09, 2013 16:25:36 ] |
Post subject: | Re: XB9 servo saver on 808 |
THANKS A LOT for your replies. Excually i will have the parts on Friday and i will test this patent on track at 21 Of April(my next race).When the parts arrive i will post again! |
Author: | Garakis(Greece) [ Fri Apr 12, 2013 19:38:58 ] | ||
Post subject: | Re: XB9 servo saver on 808 | ||
That's it.Now the only think i need is to test it.
|
Author: | Garakis(Greece) [ Tue Apr 23, 2013 17:40:49 ] |
Post subject: | Re: XB9 servo saver on 808 |
AND YES.THIS PATENT IS AMAZING. The car is 10 times better that before,i could push it on corners more than ever.The only thing i don't like is the behavior at the jumps,the car is a little bit unstable but if you are good driver you can handle it. Some tips for this patent. I used protek servo horn XB9's servo saver composite part It's better to use pyramid pack and not a flat pack. Thanks for reading this,i hope you guys try it too. |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |