XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Xray Clutch Setup https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=9&t=114 |
Page 5 of 7 |
Author: | fearsome [ Fri Nov 12, 2004 09:23:19 ] |
Post subject: | Xray Flywheel |
After closer inspection!!!! ![]() ![]() ![]() ![]() only after 30min of running. As you can see the flywheel is still almost new no scratches or other damage. http://www.rcpics.net/view_single.php?medid=42668 http://www.rcpics.net/view_single.php?medid=42667 |
Author: | gustavsen [ Wed Nov 17, 2004 21:43:00 ] |
Post subject: | |
Author: | gustavsen [ Fri Nov 19, 2004 19:39:54 ] |
Post subject: | |
Author: | z-man [ Fri Nov 19, 2004 21:34:07 ] |
Post subject: | |
Author: | idar66 [ Mon Nov 22, 2004 01:24:16 ] |
Post subject: | re clutch |
Author: | BuLLdoGG [ Mon Nov 22, 2004 06:08:14 ] |
Post subject: | |
Author: | JerKap [ Mon Nov 22, 2004 06:17:51 ] |
Post subject: | 1.1 |
Author: | idar66 [ Mon Nov 22, 2004 07:00:35 ] |
Post subject: | re clutch |
Author: | Rich Panganiban [ Mon Nov 22, 2004 18:05:42 ] |
Post subject: | |
Author: | BuLLdoGG [ Mon Nov 22, 2004 18:06:53 ] |
Post subject: | Re: re clutch |
Author: | tkbr0wn [ Tue Nov 23, 2004 07:14:42 ] |
Post subject: | |
Author: | z-man [ Tue Nov 23, 2004 12:48:33 ] |
Post subject: | |
Author: | TMizzle [ Tue Nov 23, 2004 15:48:00 ] |
Post subject: | |
Author: | showtime [ Tue Nov 23, 2004 15:49:15 ] |
Post subject: | |
Author: | Rich Panganiban [ Tue Nov 23, 2004 18:10:28 ] |
Post subject: | |
If I'm not mistaken, the XB8 flywheel is 2mm smaller diameter than the Mugen to accommodate a lower engine mount, thereby lowering the cg even further. |
Author: | BuLLdoGG [ Tue Nov 23, 2004 19:00:38 ] |
Post subject: | |
I have a Mugen flywheel and it's 35mm, the xray one is 33mm. Ofcourse there's the possibility that Mugen has more than one size flywheel. |
Author: | z-man [ Tue Nov 23, 2004 20:12:34 ] |
Post subject: | |
ok can someone clear this up? i want to use a flywheel and my LHS doesnt have the xb8 parts. so what mugen one was 33 mm. there is no way i would shim my motor to get it to work. i want it low where it belongs. |
Author: | David Joor [ Wed Nov 24, 2004 00:00:17 ] |
Post subject: | |
Author: | pbfoot [ Wed Nov 24, 2004 01:34:35 ] |
Post subject: | |
Author: | BuLLdoGG [ Wed Nov 24, 2004 05:26:25 ] |
Post subject: | |
Page 5 of 7 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |