| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Q&A with Paul Lemieux https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=8868 |
Page 1 of 27 |
| Author: | Paul LeMieux [ Mon Feb 23, 2009 19:20:37 ] |
| Post subject: | Q&A with Paul Lemieux |
| Author: | Eric Anderson [ Mon Feb 23, 2009 20:15:27 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Tue Feb 24, 2009 00:38:29 ] |
| Post subject: | |
| Author: | Gray63 [ Tue Feb 24, 2009 00:48:52 ] |
| Post subject: | SHOCKING! |
| Author: | Miller Time [ Tue Feb 24, 2009 03:31:43 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Tue Feb 24, 2009 17:53:05 ] |
| Post subject: | Re: SHOCKING! |
| Author: | Paul LeMieux [ Tue Feb 24, 2009 17:59:07 ] |
| Post subject: | |
| Author: | Gray63 [ Tue Feb 24, 2009 19:26:24 ] |
| Post subject: | |
| Author: | Miller Time [ Tue Feb 24, 2009 19:56:23 ] |
| Post subject: | |
| Author: | rx7ttlm [ Wed Feb 25, 2009 06:33:30 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Wed Feb 25, 2009 18:49:49 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Wed Feb 25, 2009 18:57:42 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Wed Feb 25, 2009 19:01:18 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Wed Feb 25, 2009 19:06:23 ] |
| Post subject: | |
| Author: | rx7ttlm [ Wed Feb 25, 2009 21:21:58 ] |
| Post subject: | |
| Author: | chris_dono [ Fri Mar 06, 2009 15:54:09 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Wed Mar 11, 2009 00:22:33 ] |
| Post subject: | |
| Author: | munrath [ Wed Mar 11, 2009 03:18:27 ] |
| Post subject: | Diff Tips |
| Author: | chris_dono [ Wed Mar 11, 2009 09:26:37 ] |
| Post subject: | |
| Author: | Paul LeMieux [ Thu Mar 12, 2009 15:06:45 ] |
| Post subject: | |
Munrath: Hi. I always start with fresh diff parts, thrust and rings especially, the carbide xray balls dont wear out that much. I sand my diff rings with 1000 grit sand papper, to do this i put the ring on the female outdrive (without the thrust assymply in it) and sand away for maybe 2min on a fresh ring ( sand circles in both directions or in a figure eight), I put a drop of bearing oil on the sand papper. for rings that have been used i will sand those with 500 grit untill the groove from running is gone, then i will finish with 1000 again. I use the xray Black grease on the thrust and iether the xray stock grease or clear stealth lube on the balls. If the diff is not good after putting in all new parts (has tight feeling spots) then replace the screw and the thrust clip. Xray is currently testing more diff lubes right now, so most likely we will have some new stuff soon. Chris: No problem. Thanks, paul |
|
| Page 1 of 27 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|