XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Maximum teeth on a '008 (spur + pinion) https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=8353 |
Page 1 of 2 |
Author: | chris_dono [ Mon Oct 13, 2008 23:21:55 ] |
Post subject: | Maximum teeth on a '008 (spur + pinion) |
Author: | PDX-Spike [ Tue Oct 14, 2008 04:22:55 ] |
Post subject: | Re: Maximum teeth on a '008 (spur + pinion) |
Author: | RGonzalez [ Tue Oct 14, 2008 07:14:37 ] |
Post subject: | |
I have run a 94 and a 96 RW spur on my sedans with no problems reaching the rear motor screw... ![]() |
Author: | Doc52 [ Tue Oct 14, 2008 08:27:01 ] |
Post subject: | |
Author: | RGonzalez [ Tue Oct 14, 2008 22:25:15 ] |
Post subject: | |
Author: | Doc52 [ Wed Oct 15, 2008 04:15:07 ] |
Post subject: | |
Author: | Doc52 [ Wed Oct 15, 2008 04:22:17 ] |
Post subject: | Re: Maximum teeth on a '008 (spur + pinion) |
Author: | PDX-Spike [ Thu Oct 16, 2008 02:41:08 ] |
Post subject: | Re: Maximum teeth on a '008 (spur + pinion) |
Author: | Doc52 [ Thu Oct 16, 2008 05:37:44 ] |
Post subject: | |
Author: | PDX-Spike [ Thu Oct 16, 2008 08:53:37 ] |
Post subject: | |
Author: | chris_dono [ Thu Oct 16, 2008 10:55:23 ] |
Post subject: | |
I'm asking because I want to know what will fit. Currently (with the kit spur) I can get to 5.1 (84 spur, 28 pinion using 1.7 internal) I want to get to a lower FDR, depending on the track and motor (I run 13.5 as well as 10.5 motors, mod's not a problem) but I know a 98 spur didn't physically fit into the 007, don't want to make the same mistake on the 008. |
Author: | PDX-Spike [ Thu Oct 16, 2008 17:48:29 ] |
Post subject: | |
Author: | chris_dono [ Thu Oct 16, 2008 19:53:36 ] |
Post subject: | |
Author: | PDX-Spike [ Fri Oct 17, 2008 03:00:58 ] |
Post subject: | |
Author: | chris_dono [ Fri Oct 17, 2008 11:06:16 ] |
Post subject: | |
Author: | adamg [ Fri Oct 17, 2008 14:03:13 ] |
Post subject: | |
Author: | chris_dono [ Fri Oct 17, 2008 14:52:49 ] |
Post subject: | |
Author: | PDX-Spike [ Fri Oct 17, 2008 22:14:11 ] |
Post subject: | |
Author: | chris_dono [ Sun Oct 19, 2008 00:26:10 ] |
Post subject: | |
Author: | Ronaldo808 [ Thu Dec 25, 2008 05:51:46 ] |
Post subject: | |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |