| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| T2 008 Problem...... https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=7177 |
Page 1 of 1 |
| Author: | kemax [ Sun Feb 24, 2008 20:49:40 ] |
| Post subject: | T2 008 Problem...... |
Hey, I have just bought and built the new T2 008, and i have the following problem. All below happens when car is on the maintenance stand: With front wheels mounted: when running straight ahead no problems, but when turning the front wheels either to the left or right it starts to vibrate and making a ogly noice. ( nothing is touching the rims ) New rims, whithout tires mounted: Same problem as above. without front wheel mounted: No problems: anyone having a surgestion. Best regards Henrik. |
|
| Author: | Doc Holiday [ Sun Feb 24, 2008 22:14:24 ] |
| Post subject: | |
hy henrik! this vibrations are normally when using spool (solid axle) and u turn left or right. but its only, if the tyres arent on the ground. if u drive with the car, there a no vibrations. and the function is without problems. cu mario |
|
| Author: | kemax [ Sun Feb 24, 2008 23:43:30 ] |
| Post subject: | |
The problem are also present when the car is on the floor, and it realy sounds unhealthy. I have seen other 008's and they don't make these strange noises when they make turns. I will not use the car until i have found the problem, because i'm sure something will brake. Cheers Herik. |
|
| Author: | Hurrle [ Sun Feb 24, 2008 23:58:30 ] |
| Post subject: | |
Do you have full steering lock? If you don't limit the steering end point this can happen. I have seen a lot of poeple recommend between 16-20 degrees of steering to each side. |
|
| Author: | YELLOWSHARK [ Mon Feb 25, 2008 09:36:50 ] |
| Post subject: | |
Kemax, if you have not adjusted your steering EPA then that is almost certainly the problem - good place to start anyway! |
|
| Author: | Tonyv [ Mon Feb 25, 2008 11:53:40 ] |
| Post subject: | |
Also take the front axles apart, thoroughly clean them and relube prior to putting them back together. If you use locktite on the set screw make sure you use a minimal amount to prevent it running into the moving parts. If the axle couplings bind just a little the added weight of rims/wheels will cause major vibration. |
|
| Author: | BRIAN77 [ Mon Feb 25, 2008 12:35:18 ] |
| Post subject: | |
it mite be a servo problem try that too |
|
| Author: | kemax [ Mon Feb 25, 2008 23:59:12 ] |
| Post subject: | |
| Author: | Tonyv [ Tue Feb 26, 2008 11:39:14 ] |
| Post subject: | |
| Author: | YELLOWSHARK [ Tue Feb 26, 2008 14:30:30 ] |
| Post subject: | |
| Author: | kemax [ Tue Feb 26, 2008 14:57:58 ] |
| Post subject: | |
Hi, Both on half and full throttle, but with most vibrations and noice on full throttle. It is not only on the maintenance stand the problem occurs, it's also on the floor. I have tried to dismount the belt, and when i turn the front wheels by hand i hear a click sound from the driveline, is it normal ? And again the car cannot be driven with this error because it looses the stability, and it makes a screeming noice when you makes turn. Cheers Henrik |
|
| Author: | Tonyv [ Tue Feb 26, 2008 18:43:20 ] |
| Post subject: | |
| Author: | kemax [ Tue Feb 26, 2008 21:16:54 ] |
| Post subject: | |
| Author: | SBH [ Tue Mar 04, 2008 09:43:45 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|