XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Broken cardan shaft https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=6924 |
Page 1 of 1 |
Author: | mcasd [ Tue Jan 15, 2008 18:29:31 ] |
Post subject: | Broken cardan shaft |
Author: | rx7ttlm [ Wed Jan 16, 2008 15:43:14 ] |
Post subject: | |
I haven't broken any, one hint tho. I think you might have overtorqued the set screw. are you breaking them in the center? and what does the break look like? did it sheer off flat? or is there some crimping or distortion? |
Author: | eppikk [ Wed Jan 16, 2008 16:14:51 ] |
Post subject: | |
Author: | mcasd [ Thu Jan 17, 2008 17:49:07 ] |
Post subject: | |
Author: | eppikk [ Thu Jan 17, 2008 19:17:55 ] |
Post subject: | |
Author: | mcasd [ Thu Jan 17, 2008 23:35:10 ] |
Post subject: | |
Hi, i used the graphite grease. May be i have to use a little bit more than i did. ... The carpet is normally used with scalers and it looses a lot of lint ball. So it could happen that there were a lot. But on the left - not broken cardan - i had no problem. Someone gave me the hint to use spring steel shafts instead of the original ones. What is your opinion about this ? Greetings mcasd |
Author: | eppikk [ Sun Jan 20, 2008 01:02:05 ] |
Post subject: | |
Author: | mcasd [ Sun Jan 20, 2008 21:19:59 ] |
Post subject: | |
Hi, i bought the EU 5 cell chassis and the drive shafts aren´t like copper but like steel..... My be, that´s the issue. I have to ask mey local dealer wether he could provide me with these spring steel shafts. Why Xray makes differences in this case ? regards mcasd |
Author: | brano [ Mon Jan 21, 2008 10:38:56 ] |
Post subject: | |
Author: | eppikk [ Thu Jan 24, 2008 18:42:38 ] |
Post subject: | |
Thats weird, i never actually seen something like that, i believe all the T2 are suposed to come with from the box. Just do as Brano said, ask the guy that sold you the car and send a mail to that adress |
Author: | Hurrle [ Thu Jan 24, 2008 22:55:50 ] |
Post subject: | |
I think you are talking about different things. Some of you are refering to the Hudy Springsteel Drive Shaft (part 305324/305323) or Drive Axle (part 305340) while others are talking about the 2x10mm pin (part 981210). Since the original poster writes that he is using the "new shafts from the upgrade kit which we were supplied with" I think he is actually talking about the pin (part 981210) that was upgraded to a new version. |
Author: | mcasd [ Sat Jan 26, 2008 21:09:12 ] |
Post subject: | |
Author: | eppikk [ Sun Jan 27, 2008 21:21:56 ] |
Post subject: | |
LOL you got me confused there, i tought it was the Hudy Spring Steel ones. I see, some guy here, once he saw the pins came loose easyly, just instaled tamyia ones... |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |