XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
'008 Electronics Layout https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=6911 |
Page 1 of 2 |
Author: | N Fucile [ Sun Jan 13, 2008 05:37:06 ] |
Post subject: | '008 Electronics Layout |
Author: | mutley001 [ Mon Jan 14, 2008 20:41:16 ] |
Post subject: | |
Author: | Steve B [ Mon Jan 14, 2008 23:34:39 ] |
Post subject: | |
Hope this helps. [/img] |
Author: | eppikk [ Wed Jan 16, 2008 16:04:34 ] |
Post subject: | |
Author: | Juan Cortez [ Thu Jan 17, 2008 03:32:49 ] |
Post subject: | |
I have an LRP as well, but because the FUTABA receiver was too big, I ended up changing it to a SPEKTRUM Here are some picks. |
Author: | ockevin [ Thu Jan 17, 2008 06:58:48 ] |
Post subject: | |
Author: | eppikk [ Thu Jan 17, 2008 19:20:49 ] |
Post subject: | |
Author: | Hurrle [ Thu Jan 17, 2008 22:59:49 ] |
Post subject: | |
Remember that the receiver shown is the Spektrum Micro receiver. The Micro version is about half the size of the "normal" Spektrum receivers. Carbon motor protector: http://www.teamxray.com/teamxray/produc ... cfd7719166 |
Author: | Juan Cortez [ Thu Jan 17, 2008 23:57:18 ] |
Post subject: | |
Thanks Hurrle, you got them all right!! ![]() Eppikk and Ockevin thanks. |
Author: | YELLOWSHARK [ Fri Jan 18, 2008 01:04:38 ] |
Post subject: | |
Engine protection bar is XR303060 |
Author: | Aus.X [ Fri Jan 18, 2008 13:22:44 ] |
Post subject: | |
Author: | Juan Cortez [ Fri Jan 18, 2008 18:54:01 ] |
Post subject: | |
Author: | GT1_Andre [ Fri Jan 18, 2008 23:05:14 ] |
Post subject: | |
Author: | Juan Cortez [ Sat Jan 19, 2008 01:32:09 ] |
Post subject: | |
Thanks, Andre...! |
Author: | beginer [ Tue Feb 05, 2008 06:04:40 ] |
Post subject: | Cleanest ever |
Author: | Damo [ Tue Feb 05, 2008 11:52:05 ] |
Post subject: | |
I third that - That is some nice tidy electronics.. I have just fitted a GTB to my T2 and I have also had to mount my reciever on the Servo. I upgraded to a GTB and a Specktrum micro reciever, but unfortunatly it does not fit down the one side any more, and where am i gonna strap that big capacitor... Personally I dont like the reciever on the Servo as i thnk it looks untidy, but hey ho.. When I used to have a MRT MX Pro and a KF302f reciever it all fitted perfectly Problem is with the GTB is that they give you 2 power cables. One is to short if the reciever is on the servo, and the other is way to long - I have colied it up with the switch wire, but not happy.. might have to get the wirecutters and soldering iron out Damo |
Author: | Juan Cortez [ Wed Feb 06, 2008 07:21:55 ] |
Post subject: | |
Thanks a lot for your comments guys. Here are some more pictures, the battery side, and how I did to hide the long cable of the motor. |
Author: | beginer [ Wed Feb 06, 2008 15:21:46 ] |
Post subject: | Thanks again |
Author: | felixc [ Thu Feb 07, 2008 02:35:15 ] |
Post subject: | lipo |
Author: | beginer [ Tue Feb 12, 2008 03:24:17 ] |
Post subject: | |
I took some pictures of my setup, since it was for an '007, I posted in a separate thread: Thanks, Michael |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |