| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Titanium Screws https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=6774 |
Page 1 of 1 |
| Author: | 1jag8 [ Mon Dec 17, 2007 03:27:03 ] |
| Post subject: | Titanium Screws |
| Author: | Hagberg [ Mon Dec 17, 2007 12:47:36 ] |
| Post subject: | |
| Author: | Hurricane '007 [ Mon Dec 17, 2007 17:21:16 ] |
| Post subject: | |
| Author: | Hurrle [ Mon Dec 17, 2007 21:09:45 ] |
| Post subject: | |
| Author: | bmc [ Mon Dec 17, 2007 22:37:08 ] |
| Post subject: | |
| Author: | Hurrle [ Mon Dec 17, 2007 23:04:22 ] |
| Post subject: | |
| Author: | Hurricane '007 [ Tue Dec 18, 2007 00:22:28 ] |
| Post subject: | |
| Author: | YELLOWSHARK [ Tue Dec 18, 2007 01:08:12 ] |
| Post subject: | |
| Author: | 1jag8 [ Tue Dec 18, 2007 01:58:42 ] |
| Post subject: | |
| Author: | YELLOWSHARK [ Tue Dec 18, 2007 02:22:49 ] |
| Post subject: | |
| Author: | Hagberg [ Tue Dec 18, 2007 13:17:50 ] |
| Post subject: | |
| Author: | darchard123 [ Thu Dec 20, 2007 17:18:48 ] |
| Post subject: | Screws |
| Author: | adamg [ Fri Dec 21, 2007 00:58:13 ] |
| Post subject: | |
| Author: | bmc [ Fri Dec 21, 2007 01:59:15 ] |
| Post subject: | |
| Author: | adamg [ Fri Dec 21, 2007 05:03:36 ] |
| Post subject: | |
| Author: | 1jag8 [ Sun Dec 23, 2007 05:43:44 ] |
| Post subject: | |
I've just replaced the steel screws with titanium and saved about 12 grams in doing so. I did not replace all the steel screws. I kept the hinge pin/roll center screws in steel. I thought that this was a high stress area and didn't want to take a chance. I also replaced the hinge pins with titanium ones for an addition 6 grams. Not alot of savings for the money but my car was 21 grams overweight and now i'm very close to where I need to be. |
|
| Author: | SLOW 77 [ Sun Dec 23, 2007 22:30:37 ] |
| Post subject: | |
| Author: | 1jag8 [ Mon Dec 24, 2007 02:16:08 ] |
| Post subject: | |
| Author: | ds motorsport [ Fri Dec 28, 2007 21:44:58 ] |
| Post subject: | |
i also like the xenon screws, i think jilles also uses them. They are avalible at the border 1jag8: how much where these custom hine pins. I've searched the entire net for a 3mm Ti rod but no company sells it. |
|
| Author: | 1jag8 [ Sat Dec 29, 2007 18:26:32 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|