XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
charging amps, what amperage do you charge at? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=663 |
Page 1 of 2 |
Author: | apexracing [ Tue Dec 21, 2004 06:01:52 ] |
Post subject: | charging amps, what amperage do you charge at? |
Hey guys, i was wondering if there could be any possible performance increase by uping the charging amps on a gp 3300, i currently charge them at 5 amps with zero delta peak, i am getting my trintiy discharge tray this week and i will be dead shorting them, is there any charge rate i should use especialy in this situation? any help apreciated. |
Author: | xray_racer [ Tue Dec 21, 2004 07:32:10 ] |
Post subject: | |
I use SMCs and according to their websight they recommend 6amp charge with a .05 peak detect. I use Integy Octane2 tray and dead short them with a 10ohm resistor. I solder the resistor while they are still on the tray to insure 0.0v. |
Author: | ldebackker [ Tue Dec 21, 2004 15:07:44 ] |
Post subject: | |
Author: | Sam_Smith [ Tue Dec 21, 2004 15:19:45 ] |
Post subject: | |
Author: | Tonyv [ Tue Dec 21, 2004 15:27:15 ] |
Post subject: | |
Author: | Dave Treacy [ Tue Dec 21, 2004 15:33:55 ] |
Post subject: | |
Author: | Sam_Smith [ Tue Dec 21, 2004 15:54:40 ] |
Post subject: | |
Author: | Tonyv [ Tue Dec 21, 2004 17:14:01 ] |
Post subject: | |
Author: | Robfo [ Tue Dec 21, 2004 18:09:30 ] |
Post subject: | |
Author: | Sam_Smith [ Tue Dec 21, 2004 18:29:07 ] |
Post subject: | |
Yeah Equalising and discharging has always been a bit of a mystery to me. I used to discharge and equalise every pack after a run but I started to notice a decline in my cells performance so now I leave my cells with charge in them after a run and just recharge them next time I want to use them. Then I discharge and equalise every 5-6 meetings. My cells haven't seemed to fall off like the other ones did. Your veiw on this would be interesting Tony?? Sam |
Author: | Tonyv [ Tue Dec 21, 2004 20:14:03 ] |
Post subject: | |
Author: | teamgp [ Tue Dec 21, 2004 21:10:36 ] |
Post subject: | |
Author: | Steve e [ Tue Dec 21, 2004 21:25:46 ] |
Post subject: | |
Author: | apexracing [ Tue Dec 21, 2004 23:03:03 ] |
Post subject: | |
I usualy charge at 5 amps, i am thinking of going up to 6 amps, i am buying 3 trinity heavymetal discharge trays and i am going to use them to dead short my batteries, i run 3 fusion gp 3300's numbers range from 1.18-1.191 i also have a few other batteries, i haven't tried the sayno 3600's yet are they worth getting?, any ways if you all have any more advice i would apreciate any tips that might help me get the edge at my lhs. thanks guys. |
Author: | Sam_Smith [ Wed Dec 22, 2004 03:58:25 ] |
Post subject: | |
I found this while surfing check out what noval have to say on the matter here>>> |
Author: | trickpatrick [ Wed Dec 22, 2004 04:52:25 ] |
Post subject: | |
Everything I have read including Novak and Orion and Trinty says Dead shorting is bad for Ni-mh Batts. And also there is no memory retention meaning you dont have to dis-charge or use the tray with Ni-mh. I use the novak tray down to .01, but do not dead short isn't that stuff for Nicads.? Rick |
Author: | apexracing [ Wed Dec 22, 2004 06:19:03 ] |
Post subject: | |
Atually almost every racer at my track ds's they're batts and there is a significant increase in voltage, at the sacrifice of a small amount of run time, takes a few races for the batteries to break in though, rc car action did a article on it, brian kinwald has been doing it for a few years now and his batteries still perform at peak level. |
Author: | Hagberg [ Thu Dec 23, 2004 01:33:52 ] |
Post subject: | |
SMC recommends 6.0 amps with 35mv delta peak, so that is what I charge with, works great! If I have time then I re-peak the battery before my run. For discharging I use a Novak Smart Tray. |
Author: | mattthegreat01 [ Thu Dec 23, 2004 04:10:05 ] |
Post subject: | |
Hi this is Matt from the USA i been racing on and off for 15 years and im still learning about battery care . What i do is after the run i discharge the pack at 30 amps and let it cool down then put then away thill i get home then i tray then on a trinty 2.5 tray .When the lights go out i put them in my box and have them ready for the next race ther i but on the novak tray and discharge them to .01 on the volt setting . When done i charge at 5.5 at 10 milvolt cut off i have never dumped at this setting and it works for me so i envite you to try this thill then have a happy holodays from the good old USA C-YA |
Author: | Ritzel [ Thu Dec 23, 2004 20:29:24 ] |
Post subject: | |
I personaly discarge my packs withe about 2A an put them on the robitronic equalzier for next race. I charge with 5.5 A to 48C (Clesius) and I try to use them as hot as possible. I noticed the punch to fade away by letting them cool down under ca. 45C (Celsius) Whats about cutting off by temperatur in generell??? |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |