| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| The new XRAY Alu shocks https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=6346 |
Page 1 of 1 |
| Author: | michelw [ Sun Oct 07, 2007 08:33:48 ] |
| Post subject: | The new XRAY Alu shocks |
Hi, I've got the new Alu shocks for my 007 recently. During the assembly, I have come across the problem of the shock rebound procedure. It seems like no matter how slow I put out and in the shcok rod, there is always the air bubbles being introduced into the shocks through this procedure. Very often when I put the shock rod slowly out, the whole set of O-rings will come off from the shock body so when I push the rod back, air is introduced into the shock body. So any suggestion to help get rid of this! Much thanks for your advice! |
|
| Author: | pilot [ Sun Oct 07, 2007 11:48:23 ] |
| Post subject: | Shocks |
When you are setting the rebound are you removing the lower cap or just loosening it a little bit?? |
|
| Author: | michelw [ Sun Oct 07, 2007 15:04:26 ] |
| Post subject: | Re: Shocks |
| Author: | pilot [ Mon Oct 08, 2007 11:36:53 ] |
| Post subject: | Shocks |
| Author: | michelw [ Mon Oct 08, 2007 16:07:10 ] |
| Post subject: | Re: Shocks |
| Author: | Martin Hudy [ Thu Oct 11, 2007 10:46:53 ] |
| Post subject: | |
| Author: | michelw [ Fri Oct 12, 2007 02:13:58 ] |
| Post subject: | |
| Author: | sukh [ Fri Nov 09, 2007 01:50:08 ] |
| Post subject: | |
| Author: | pilot [ Fri Nov 09, 2007 06:02:40 ] |
| Post subject: | Shocks |
| Author: | sukh [ Sat Nov 10, 2007 07:04:02 ] |
| Post subject: | |
| Author: | pilot [ Sun Nov 11, 2007 02:01:15 ] |
| Post subject: | Shocks |
| Author: | sukh [ Sun Nov 11, 2007 02:53:35 ] |
| Post subject: | |
| Author: | teamgp [ Sun Nov 11, 2007 15:01:06 ] |
| Post subject: | |
| Author: | sukh [ Mon Nov 12, 2007 04:24:18 ] |
| Post subject: | |
Unfortunately there is no Xray team driver’s in the Toronto area, but I did talk to a few guys at Fastcats today and they had the same problem, but there were able to bleed them thru the top by pushing down on the rubber membrane, still a pain to get the rebound on all four shocks the same but should work I guess, I will try tomorrow, I can almost guarantee that you can not set the rebound properly without getting any air into the shocks by following the instructions, I think Xray should revise them but they do work for the normal plastic shocks. |
|
| Author: | sukh [ Wed Nov 14, 2007 01:05:25 ] |
| Post subject: | |
| Author: | teamgp [ Wed Nov 14, 2007 02:46:18 ] |
| Post subject: | |
| Author: | Martin Hudy [ Thu Nov 15, 2007 13:28:08 ] |
| Post subject: | |
| Author: | teamgp [ Thu Nov 15, 2007 16:39:02 ] |
| Post subject: | |
| Author: | sukh [ Sat Nov 17, 2007 04:01:07 ] |
| Post subject: | |
| Author: | holger [ Tue Dec 18, 2007 16:15:28 ] |
| Post subject: | Aluminium Shock and T2 008 |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|