XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Roll centre adjustments https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=5273 |
Page 1 of 1 |
Author: | ianp [ Fri Apr 13, 2007 09:10:08 ] |
Post subject: | Roll centre adjustments |
Author: | Tonyv [ Fri Apr 13, 2007 11:52:29 ] |
Post subject: | |
Author: | ianp [ Fri Apr 13, 2007 12:38:23 ] |
Post subject: | |
Author: | Tonyv [ Fri Apr 13, 2007 12:53:11 ] |
Post subject: | |
Author: | Chicane [ Fri Apr 13, 2007 14:47:55 ] |
Post subject: | |
Author: | jaxgough [ Fri Apr 13, 2007 16:34:57 ] |
Post subject: | |
Author: | Chris08527 [ Sat Apr 14, 2007 01:16:44 ] |
Post subject: | |
tony what do you mean by camber gain??? and how do you adjust that??? |
Author: | Tonyv [ Sun Apr 15, 2007 05:08:10 ] |
Post subject: | |
The locater pin is directly in line with the pivot ball. I.e if the pin is inside and up then so is the pivot ball. Camber gan, camber change, camber rise are all used to refer to the same thing, namely how much the camber angle changes when the suspension is suppressed. Camber rise (as it is referred to in the T2 setup book) can be changed by changing the lenght of the camber link (also referred to as top link) and by changing the angle of the camber link compared to the lower suspension arm. |
Author: | Chris08527 [ Mon Apr 23, 2007 03:29:42 ] |
Post subject: | |
Author: | Tonyv [ Mon Apr 23, 2007 17:41:11 ] |
Post subject: | |
Can you post a link to your setup? |
Author: | Chris08527 [ Tue Apr 24, 2007 00:58:16 ] |
Post subject: | |
tony i posted it on the x-ray site here is a link hope it works xform/index.php?act=view&ID=604&setup=t2_007 Chris08527 track jackson rc for some reason i cant post the link can you just do a search on the set-ups page??? thanks Chris |
Author: | Tonyv [ Tue Apr 24, 2007 11:08:51 ] |
Post subject: | |
Author: | Chris08527 [ Tue Apr 24, 2007 11:46:39 ] |
Post subject: | |
Author: | Chris08527 [ Mon Apr 30, 2007 04:54:45 ] |
Post subject: | |
hey tony basically did everything you suggested to the car except change the ackerman angle becuase i wasnt sure if you wanted me to do it thought he steering block or the servo saver??? the car was much better had steering, little bit of the rear end loose thing was me over driving the car . . .forgot carpet season is over now if i really wanted to be picky the car felt a little tight with fresh tires can you take a look at set up #2 and make any suggestions thanks Chris |
Author: | Tonyv [ Mon Apr 30, 2007 19:30:15 ] |
Post subject: | |
Chris, what do you mean exactly when you say the car felt a bit "tight" on fresh tyres? |
Author: | Chris08527 [ Mon Apr 30, 2007 23:04:15 ] |
Post subject: | |
can didnt want to rotate the car was very good but i think it could be a little better |
Author: | Tonyv [ Tue May 01, 2007 13:57:14 ] |
Post subject: | |
Author: | Chris08527 [ Wed May 02, 2007 01:09:02 ] |
Post subject: | |
Author: | Tonyv [ Wed May 02, 2007 09:54:24 ] |
Post subject: | |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |