XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
T2 007 Chassis on T2? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=4402 |
Page 1 of 2 |
Author: | Pasqual [ Mon Oct 23, 2006 17:04:49 ] |
Post subject: | T2 007 Chassis on T2? |
T2 Chassis 2.5mm Graphite - Rubber-Spec - Multi-Flex™ Will the T2 007 chassis fit on a normal T2? If you look by specs it says it will fit, but i want to know it for sure. Thanks. |
Author: | Tonyv [ Mon Oct 23, 2006 17:20:31 ] |
Post subject: | |
Yes, both the EU and US versions of the T2'007 chassis will fit on both the T2 and T2R models. |
Author: | Pasqual [ Mon Oct 23, 2006 18:11:41 ] |
Post subject: | |
Oke ![]() Thanks |
Author: | TKG26 [ Wed Oct 25, 2006 13:50:39 ] |
Post subject: | |
but u need new bulkheads yes or no? The conversion set should have all of that? |
Author: | brano [ Wed Oct 25, 2006 14:17:45 ] |
Post subject: | |
You can use the chassis from T2'007 also on T2 and T2R cars, but you do not need the bulkheads. The bulkheads you will need when you want to use also T2'007 top deck, rear top deck, and quick servo saver. The conversion sets should include all parts so you can upgrade your T2 or T2R to T2'007 cars. |
Author: | Pasqual [ Wed Oct 25, 2006 15:27:37 ] |
Post subject: | |
Author: | NERO [ Wed Oct 25, 2006 16:11:15 ] |
Post subject: | |
Author: | Tonyv [ Wed Oct 25, 2006 17:25:09 ] |
Post subject: | |
Author: | Pasqual [ Thu Nov 02, 2006 16:01:32 ] |
Post subject: | |
Author: | Tonyv [ Thu Nov 02, 2006 16:22:39 ] |
Post subject: | |
Author: | Pasqual [ Thu Nov 02, 2006 16:35:21 ] |
Post subject: | |
Author: | Tonyv [ Thu Nov 02, 2006 19:02:36 ] |
Post subject: | |
Author: | Joep [ Thu Nov 02, 2006 20:14:07 ] |
Post subject: | |
Author: | Pasqual [ Fri Nov 03, 2006 10:11:30 ] |
Post subject: | |
Joep that's the place where i ordered the Chassis, but it isn't in stock. I will send a mail to xray. |
Author: | Joep [ Fri Nov 03, 2006 16:30:15 ] |
Post subject: | |
Author: | Pasqual [ Wed Dec 06, 2006 22:07:30 ] |
Post subject: | |
After some weeks the chassis is on my T2. But there is a small problem ![]() The servo holes are more to the center of de chassis. So my servo can't move because it hits the top deck. I already have a shime between the servo and the servo stands but stil not enough clearance. I downloaded the manual of the 007 and i see they use an other kind of screw in de servo horn. I will order that item but if there is still not enough clearance do i need to put a thicker shim between servo and servo stands or can i remove some material on the topdeck? Hoop some one can tell me that thnx. |
Author: | Joep [ Wed Dec 06, 2006 23:58:06 ] |
Post subject: | |
Author: | TKG26 [ Thu Dec 07, 2006 05:48:25 ] |
Post subject: | |
since xray don't support hitec servo horns i use a kimbro with some dremel work. As u can see i had to shim out and the horn does not touch the top deck it has about .5mm or clearance |
Author: | Nova Racer [ Thu Dec 07, 2006 17:34:00 ] |
Post subject: | |
Just wondering about making the T-2 into the 007 version.... Is there info on the differences between these 2? |
Author: | brano [ Thu Dec 07, 2006 18:21:12 ] |
Post subject: | |
All parts that you will need to convert T2 or T2R to T2'007 you can find here at or |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |