| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| DROOP SETTINGS FOR FK05 https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=2695 |
Page 1 of 1 |
| Author: | neil876 [ Wed Dec 07, 2005 01:46:14 ] |
| Post subject: | DROOP SETTINGS FOR FK05 |
| Author: | ALBERTO [ Wed Dec 07, 2005 03:00:27 ] |
| Post subject: | |
| Author: | neil876 [ Wed Dec 07, 2005 03:12:54 ] |
| Post subject: | |
| Author: | ALBERTO [ Wed Dec 07, 2005 05:30:55 ] |
| Post subject: | |
| Author: | neil876 [ Wed Dec 07, 2005 11:49:35 ] |
| Post subject: | |
| Author: | Eyeball [ Wed Dec 07, 2005 13:34:09 ] |
| Post subject: | |
| Author: | neil876 [ Wed Dec 07, 2005 14:22:36 ] |
| Post subject: | |
| Author: | ALBERTO [ Wed Dec 07, 2005 14:52:59 ] |
| Post subject: | |
| Author: | neil876 [ Wed Dec 07, 2005 15:11:48 ] |
| Post subject: | |
| Author: | Eyeball [ Thu Dec 08, 2005 03:47:50 ] |
| Post subject: | |
| Author: | ALBERTO [ Thu Dec 08, 2005 08:26:47 ] |
| Post subject: | |
| Author: | Eyeball [ Thu Dec 08, 2005 11:56:40 ] |
| Post subject: | |
| Author: | cbcbcb [ Thu Dec 08, 2005 12:57:53 ] |
| Post subject: | |
| Author: | ALBERTO [ Thu Dec 08, 2005 13:15:26 ] |
| Post subject: | |
| Author: | cbcbcb [ Thu Dec 08, 2005 13:22:01 ] |
| Post subject: | |
| Author: | ALBERTO [ Thu Dec 08, 2005 16:14:28 ] |
| Post subject: | |
| Author: | Sailfish [ Thu Dec 08, 2005 17:30:25 ] |
| Post subject: | |
| Author: | Eyeball [ Mon Dec 12, 2005 02:58:29 ] |
| Post subject: | |
| Author: | ALBERTO [ Mon Dec 12, 2005 04:27:30 ] |
| Post subject: | |
Eyeball....... i dont mean to ruffle any feathers here.... But if you look at ralph burch's set up sheet, where he has the droop settings. it specifically says front droop mesured under screw of c hub. And rear droop is mesured under BLOCK...... when i was explaining this to cbcbcb i was refurring to the rear of the car (block) not the front. As what we were clearly discussing in an earlyer post  
If I am wrong it is beacuse i am using these setup sheets as my reference... |
|
| Author: | Eyeball [ Mon Dec 12, 2005 06:07:11 ] |
| Post subject: | |
Alberto, you're not wrong in any way if you're following someone else's setup sheet as that will be the true measurement obviously, and you're not ruffling any feathers either. 
I was just under the impression that you were supposed to measure under the screws but in actual fact, looking at the FAQ it does say drivers will post where the measurement was actually made, so my apologies. S 
|
|
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|