XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Lower 0.75mm Eccentric Suspension Holder https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=2360 |
Page 1 of 2 |
Author: | Dave Treacy [ Sat Oct 08, 2005 01:09:00 ] |
Post subject: | Lower 0.75mm Eccentric Suspension Holder |
I've just got hold of these and just want to confirm that they are installed as a direct replacement using the middle holes on the rear bulkheads... True? |
Author: | vadn1 [ Sat Oct 08, 2005 01:48:56 ] |
Post subject: | |
Author: | polesitter61 [ Sat Oct 08, 2005 02:46:30 ] |
Post subject: | |
Author: | dnte5 [ Sat Oct 08, 2005 04:12:06 ] |
Post subject: | |
Author: | Eyeball [ Sat Oct 08, 2005 05:57:07 ] |
Post subject: | |
Author: | littleal [ Sat Oct 08, 2005 10:11:53 ] |
Post subject: | Re: Lower 0.75mm Eccentric Suspension Holder |
Author: | teamgp [ Mon Oct 10, 2005 17:00:17 ] |
Post subject: | |
Author: | Dave Treacy [ Tue Oct 11, 2005 14:30:15 ] |
Post subject: | |
OK, me confucious with the responses... ![]() At the moment we are running the kit ones in the middle holes. If I put the .75's in the middle holes then the roll centre will be lowered, but if I out them in the top hole the roll centre will be raised (from my current position)? If this is the case, what are the benefits / disadvantages for both settings...or should I stay as I am. I initially thought that they were to be used with the middlle ones as you cannot fit the kit ones ot the lower holes due to the design of the chassis... |
Author: | fulcrum2 [ Tue Oct 11, 2005 14:52:28 ] |
Post subject: | |
How about lowering or raising the roll center just a little bit? Smaller steps? This is probably the reason for the new holders. Or adding just a little bit of anti dive or kick up... |
Author: | teamgp [ Tue Oct 11, 2005 17:32:21 ] |
Post subject: | |
Author: | Eyeball [ Wed Oct 12, 2005 02:09:03 ] |
Post subject: | |
Author: | vadn1 [ Wed Oct 12, 2005 04:33:50 ] |
Post subject: | |
Author: | teamgp [ Wed Oct 12, 2005 15:21:05 ] |
Post subject: | |
Author: | projectnmt [ Wed Oct 12, 2005 19:19:08 ] |
Post subject: | |
Author: | teamgp [ Wed Oct 12, 2005 20:17:34 ] |
Post subject: | |
Author: | Mark Christopher [ Thu Nov 10, 2005 12:57:04 ] |
Post subject: | |
team gp you use em front and rear or just rear? |
Author: | teamgp [ Thu Nov 10, 2005 18:18:05 ] |
Post subject: | |
Author: | Mark Christopher [ Thu Nov 10, 2005 20:28:40 ] |
Post subject: | |
i understand they can do both, have ordered 2 sets to try |
Author: | drsfly [ Thu Nov 10, 2005 22:46:51 ] |
Post subject: | .75 lower suspension holders? |
Author: | Sailfish [ Fri Nov 11, 2005 01:14:43 ] |
Post subject: | |
Page 1 of 2 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |