| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| question for Alex (PF ltcr) https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=18580 |
Page 1 of 1 |
| Author: | picchio78 [ Sat Mar 01, 2014 12:39:24 ] |
| Post subject: | question for Alex (PF ltcr) |
Hello, i would like to know how to drill holes in the body.To get more front grip should be placed ahead or behind? Like setting according to the grip of the asphalt track? Thanks and excuse my english!! |
|
| Author: | promodvette [ Sun Mar 02, 2014 22:24:35 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
For more from grip you will want to move the body forward. So your holes would be behind your normal ones, as in closer to windscreen. |
|
| Author: | picchio78 [ Sun Mar 02, 2014 22:50:26 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
Ok, as recommended to drill? Do I usually coincide pin ecs front passes in the middle of the skip wheel |
|
| Author: | promodvette [ Mon Mar 03, 2014 04:36:52 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
Using the factory scribed wheel cutouts on the ltc-r, I measure to make a center line between them. This photo shows current position on my car that about 2.75mm forward from centerline. This is for a lower grip carpet. It is only slightly more aggressive than center mounted position. You can try 5mm forward and see if it helps. Alexander should be back in a day or 2 and tell us what he did for the ETS race. |
|
| Author: | picchio78 [ Tue Mar 04, 2014 09:55:33 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
ok ,thank you very nice! |
|
| Author: | Hagberg [ Tue Mar 11, 2014 11:50:26 ] | ||
| Post subject: | Re: question for Alex (PF ltcr) | ||
This is how I measure it. The center of the body post to the bottom edge of the front windscreen. I usually mount my body quite a bit forward for more steering overall. I use these measurements: LTC-R: 74.5mm SP6: 71 GX: 74.5
|
|||
| Author: | picchio78 [ Fri Mar 14, 2014 08:49:43 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
ok,thanks!! |
|
| Author: | Justin Cornett [ Fri Mar 21, 2014 16:54:18 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
| Author: | Hagberg [ Tue Mar 25, 2014 19:16:27 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
| Author: | Skiddins [ Sun Feb 01, 2015 01:57:32 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
Hi Alex, do you have a similar measurement for the new Dodge Dart bodyshell? |
|
| Author: | Salkin [ Mon Feb 02, 2015 10:27:16 ] |
| Post subject: | Re: question for Alex (PF ltcr) |
And I would like to add to the question to Hagberg, does the measurements still apply for the 2015 version, as I suppose that the measurements given here are for the 2014 version. |
|
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|