XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
New beginning https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=18480 |
Page 1 of 1 |
Author: | TSRacing [ Sat Dec 21, 2013 21:58:27 ] |
Post subject: | New beginning |
Hi to everyone! my name is TS and i'm came back to RC cars after a couple of years of inactivity! My T4 has been delivered today and I' ve started the assembly this afternoon! First impression it's the high quality of graphite and plastic, but for drive impressions I' ve have to wait! ![]() If anyone have some tips or tricks for the assembly regarding this car I really appreciate! I live in Italy and my operative base it' s Segrate so if someone live near me or want to make a visit at this track we can find there for a day of test together! ![]() |
Author: | Skiddins [ Sun Dec 22, 2013 00:15:27 ] |
Post subject: | Re: New beginning |
Everyone seems to buy the optional graphite bumper brace to prevent damage to the chassis in a crash; Welcome to Xray ![]() |
Author: | TSRacing [ Sun Dec 22, 2013 14:44:17 ] |
Post subject: | Re: New beginning |
Ehi, nice to know you and thanks for your reply. Here in Italy this part it's sold in a kit called XRAY T4 Italia which contains also the ECS shaft for front wheels! I think in my next order I will insert this piece, thank you for the tip! ![]() |
Author: | Green Wing [ Sun Dec 22, 2013 21:22:45 ] |
Post subject: | Re: New beginning |
Hello, maybe the following parts for service: http://www.teamxray.com/teamxray/produc ... %20%282%29 Especially in the front the CVDs should be checked regularly for pin wear as you can't see it when the CVDs are assembled. If you do so there will be almost no wear on the couplers and the driveshafts on the T4. http://www.teamxray.com/teamxray/produc ... %20%284%29 These caps need to be replaced "regularly", specially when using powerful motors and/or in high grip conditions. |
Author: | Hagberg [ Mon Dec 23, 2013 21:42:40 ] |
Post subject: | Re: New beginning |
CA glue edges of chassis to prevent delamination. Make sure everything is moving freely. Don't overfill the gear differential. Use a sufficient amount of graphite grease on drive shaft joints. I use the following option parts: 301213 UPPER GRAPHITE HOLDER FOR BUMPER 302190 GRAPHITE FRONT LOWER ARM PLATE 1.6MM (2) 302169 FRONT SUSPENSION ARM - GRAPHITE - 1-HOLE 303169 REAR SUSPENSION ARM - GRAPHITE - 1-HOLE 303190 GRAPHITE REAR LOWER ARM PLATE 1.6MM (2) 303440 ALU ANTI-ROLL BAR COLLAR (2) 303493 T4 ANTI-ROLL BAR REAR 1.3 MM 305330 ECS DRIVE SHAFT 52MM WITH 2MM PINS 305434 LOW FRICTION KEVLAR DRIVE BELT FRONT 3 x 513 MM 305447 LOW FRICTION KEVLAR DRIVE BELT REAR 3 x 189 MM 306516-O T4 ALU TOP DECK MOUNT - ORANGE 308031-O ALU XRAY SHOCK SPRING RETAINING COLLAR 308264 XRAY 4S SPRING-SET PROGRESSIVE C=2.5-2.8 (2) 308276 XRAY 4S SPRIN G-SET C=2.7 (2) spare parts which are good to have: 302253 COMPOSITE STEERING BLOCK - HARD - V2 302363 COMPOSITE C-HUB RIGHT - 4° DEG. - MEDIUM 302364 COMPOSITE C-HUB LEFT - 4° DEG. - MEDIUM 305135 COMPOSITE SOLID AXLE DRIVESHAFT ADAPTERS (2) 305241 DRIVE SHAFT REPLACEMENT PLASTIC CAP 3.5 MM (4) |
Author: | TSRacing [ Tue Dec 24, 2013 14:34:46 ] |
Post subject: | Re: New beginning |
Oh thanks for the tips Alex, nice to know you, so regarding chassis, arms, drive shafts it's already check and OK, for the rest I want before to know the car and understand where I have to work for adapt at my driving style but I will store your list of parts for future reference! Thanks again and Merry Christmas! ![]() |
Author: | andrewd [ Tue Dec 24, 2013 21:25:06 ] |
Post subject: | Re: New beginning |
That's a good list to work off. What would you say are the better the linear or progressive spring sets |
Author: | Hagberg [ Thu Dec 26, 2013 19:14:03 ] |
Post subject: | Re: New beginning |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |