| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| managed to bend..... https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=1724 |
Page 1 of 2 |
| Author: | lukehobson [ Wed Jun 01, 2005 11:53:41 ] |
| Post subject: | managed to bend..... |
| Author: | Joep [ Wed Jun 01, 2005 12:24:15 ] |
| Post subject: | |
Oh yes 
I managed Saterday after some radio interference to crash into the pit lane wall, made off concrete and bend my lower inside pivot axle in the rear. Aprox. 15 degrees.. 1 plastic pivot holder was broken and both srews were screwed 
So the plastic did win from the hardened steel... |
|
| Author: | michelle [ Wed Jun 01, 2005 12:37:25 ] |
| Post subject: | |
iv managed to bent 2 front drive shafts at the same time before i had already broken a c hub so i was coming down the straight to get the car to my dad so he could take it off the track for me and this guys motor seized up in front of me and i ened up running straight into the back of him
it didnt touch his TC3 though |
|
| Author: | John Thornhill [ Wed Jun 01, 2005 22:20:39 ] |
| Post subject: | |
| Author: | Joep [ Wed Jun 01, 2005 23:52:50 ] |
| Post subject: | |
I'm not complaining about the rear construction 
I'm absolutely happy with the the fact that the pivot holders and screws are not stronger than the bulkheads. And I had some extra hardened steel axles with me, so I drove again in 10 minutes 
|
|
| Author: | apexracing [ Thu Jun 02, 2005 04:39:48 ] |
| Post subject: | |
| Author: | Gazteb [ Thu Jun 02, 2005 10:59:42 ] |
| Post subject: | |
| Author: | lukehobson [ Thu Jun 02, 2005 15:03:48 ] |
| Post subject: | |
hi gaz, yep i modified it just a little for 19t but nothing too magor, my friend managed to bend the post in the servo saver that you mentioned, i think you have to buy the whole assembly (well he did at least lol) yep i'll sure be there at stafford, luke |
|
| Author: | Gazteb [ Thu Jun 02, 2005 17:15:18 ] |
| Post subject: | |
| Author: | lukehobson [ Thu Jun 02, 2005 17:30:07 ] |
| Post subject: | |
| Author: | Evo2 Mart [ Mon Jun 06, 2005 13:48:13 ] |
| Post subject: | |
Nope, nothing else broke. I've managed to straighten the pivot pin since though and it dos'nt seem to have any effect on the steering. The only thing I broke at Bedworth was a rear shock and a rear arm, after I backed it into the wall while going flat out
Martin See you all at Stafford 
|
|
| Author: | Gazteb [ Mon Jun 06, 2005 17:47:56 ] |
| Post subject: | |
| Author: | lukehobson [ Mon Jun 06, 2005 20:00:05 ] |
| Post subject: | |
if anybody bends another one during a BTCC or BRCA stock national meeting i have a servo saver assembaly from the raycer if anybody is in need of 1. just come and see me ( i normally pit at the orange VW camper at btcc and grey shed like volvo at brca lol ) luke |
|
| Author: | Evo2 Mart [ Tue Jun 07, 2005 00:01:22 ] |
| Post subject: | |
| Author: | lukehobson [ Tue Jun 07, 2005 12:15:14 ] |
| Post subject: | |
| Author: | Joep [ Tue Jun 07, 2005 13:08:01 ] |
| Post subject: | |
| Author: | lukehobson [ Mon Jun 27, 2005 08:38:34 ] |
| Post subject: | |
| Author: | ben [ Mon Jun 27, 2005 13:44:09 ] |
| Post subject: | |
Hi Luke, i am afraid you can only buy them as a set of 4 
Ben
|
|
| Author: | teamgp [ Mon Jun 27, 2005 15:27:13 ] |
| Post subject: | |
I've stripped a screw into the right rear bulkhead and demolished the threads trying to get it out. If anyone in the US has bought an extra set to use any of the other bulkheads from the set, please PM me so I can purchase a right rear from you. I'm paypal ready! Thanks. |
|
| Author: | AL [ Mon Jun 27, 2005 17:13:42 ] |
| Post subject: | |
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|