@moggy - If you want to pm me your paypal details or how you'd like me to pay I will happily take you up on the offer. Upon receipt I will get the money to you asap to ensure quick despatch. You know what it's like when you want to try these things.
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Help needed! https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=12399 |
Page 1 of 1 |
| Author: | anthonybirch1983 [ Wed Feb 22, 2012 15:05:33 ] |
| Post subject: | Help needed! |
I hope this doesn't sound a daft question but I purchased my T3 second-hand a few weeks ago. I noticed the other night that to the rear of the car in a number of pictures I've seen, there are two supports to either side of the top deck near where the motor is located. It looks as thought they are there to offer additional support to the top deck. I wasn't supplied these with the car and would like to purchase them. My question is to do with the screws required to support this in place. As you can appreciate I am unsure of the required length and wondered if someone could shed any light on this for me? This picture shows the location of the above mentioned part: In addition to the above query I wondered if any help could be offered with another question I have. Currently I run a spool in the front of the car and have had a few problems with the cups that screw into the spool on either side for the driveshafts to locate in. I have broke a few of these already and wondered if there is an optional part to improve this area. Metal cups etc? Thanks in anticipation of your response. |
|
| Author: | Bytestream [ Wed Feb 22, 2012 18:48:26 ] |
| Post subject: | Re: Help needed! |
The Standoffs are part no. 306515-K The Screws needed are (2) 3x6mm Button Head and (2) 3x6mm Flat Head Here is the page where you can find all that out .. http://www.teamxray.com/teamxray/produc ... U%20Rubber The aluminum outdrives for the spool are part no. 305137 |
|
| Author: | cypher [ Wed Feb 22, 2012 20:07:49 ] |
| Post subject: | Re: Help needed! |
| Author: | anthonybirch1983 [ Wed Feb 22, 2012 22:14:02 ] |
| Post subject: | Re: Help needed! |
@Bytestream - Thanks for your reply. Let's just say the shopping list is nearing completion. lol @cypher - THanks for your reply too. I am running a Nosram 13.5t Storm Evolution brushless on a Speed Pasison GT 2.1 Prostock ESC. Everything also appears to be moving freely on the front end too. Not sure if that will help? |
|
| Author: | moggy12 [ Thu Feb 23, 2012 09:00:14 ] |
| Post subject: | Re: Help needed! |
you need 3 off these top deck posts one goes behind front sterring assemble i have the 3 with screws £5 posted let me know |
|
| Author: | anthonybirch1983 [ Thu Feb 23, 2012 12:18:22 ] |
| Post subject: | Re: Help needed! |
@moggy - If you want to pm me your paypal details or how you'd like me to pay I will happily take you up on the offer. Upon receipt I will get the money to you asap to ensure quick despatch. You know what it's like when you want to try these things.
|
|
| Author: | moggy12 [ Thu Feb 23, 2012 12:53:15 ] |
| Post subject: | Re: Help needed! |
| Author: | anthonybirch1983 [ Thu Feb 23, 2012 12:59:09 ] |
| Post subject: | Re: Help needed! |
Replied a money sent! 
|
|
| Author: | moggy12 [ Thu Feb 23, 2012 13:03:35 ] |
| Post subject: | Re: Help needed! |
| Author: | anthonybirch1983 [ Thu Feb 23, 2012 13:15:02 ] |
| Post subject: | Re: Help needed! |
lol. If you have any further bits you feel may be of interest to me don't hesitate to let me know. Currently collecting spares and bits for when those little mishaps happen. lol |
|
| Author: | moggy12 [ Thu Feb 23, 2012 13:58:49 ] |
| Post subject: | Re: Help needed! |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|