Hello, I attached 2 images.
I hope you help.
Regards.
| Attachments: |
|
2.jpg [ 162.91 KiB | Viewed 2267 times ] |
|
1.jpg [ 81.02 KiB | Viewed 2267 times ] |
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| ETS Round 3 Pinion size https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=12392 |
Page 1 of 1 |
| Author: | kalungaio [ Sat Feb 18, 2012 11:39:15 ] |
| Post subject: | ETS Round 3 Pinion size |
Hi guys, what are your opinion about pinon size to use and spur gear to use in the net round of ETS at Canaries? Thanks in advance. |
|
| Author: | Stanley Bąk [ Sat Feb 18, 2012 12:10:28 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
depands on class in pro stock the lowest fdr is 4.0 on asphalt(am i right?) so i will use 76 spur and 36 pinion |
|
| Author: | kalungaio [ Sat Feb 18, 2012 13:57:16 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
OK so there is a FDR limit of 4.0 ? Thanks, I'll have to buy some spurs and pinions. Maximum I have is 34. |
|
| Author: | Stanley Bąk [ Sat Feb 18, 2012 15:28:38 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
but im talking about 48dp 4.5 is 76 and 32 |
|
| Author: | kalungaio [ Sat Feb 18, 2012 22:53:28 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
Ok me too 48dp Stock Class. Just confirm there is a FDR limit of 4.0 or 4.5 ? |
|
| Author: | Stanley Bąk [ Sun Feb 19, 2012 00:09:26 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
im not 100 sure,but on asphalt it is 4.0 and carpet is 4.5 am i right? can someone confirm this? |
|
| Author: | David_Ehrbar [ Sun Feb 19, 2012 12:23:18 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
Last year in Apeldoorn and Andernach it was 4.0. On Anna's car we used 37/78*1,9=4,005. But you have to modify the motor mount a little bit... |
|
| Author: | Ruben_qlc [ Tue Feb 21, 2012 14:17:22 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
Hello friends. I am from Canary Islands. People of Xray, we are using 48p, with spur 78 and pinion 37, ratio: 4.005 as David_Ehrbar says. But I must modify the motor mount, where you put the screws more or less 0.5mm, and in the center part. Regards. |
|
| Author: | likeslowww [ Thu Feb 23, 2012 19:22:42 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
Hello xray users! I am also the new user of T3 12 and I must say it is awesome car. @David, Ruben: could you please describe me (or show me with picture) your modification to fit 37 pinion? Thank you. |
|
| Author: | Ruben_qlc [ Fri Feb 24, 2012 01:03:00 ] | |||
| Post subject: | Re: ETS Round 3 Pinion size | |||
Hello, I attached 2 images. I hope you help. Regards.
|
||||
| Author: | likeslowww [ Fri Feb 24, 2012 11:25:04 ] |
| Post subject: | Re: ETS Round 3 Pinion size |
Thank you Ruben. Everything is clear now. I just ordered pinion and spur for my T3. |
|
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|