| Attachments: |
|
zoom_52118917_302076.jpg [ 108.75 KiB | Viewed 6315 times ] |
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Eccenter on setup sheets https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=12082 |
Page 1 of 1 |
| Author: | Quietman [ Sat Dec 24, 2011 13:16:00 ] |
| Post subject: | Eccenter on setup sheets |
Hi What is eccenter and what does it do? Seen it on the setupsheets but cant think what it would be? Thanks Happy christmas and new year |
|
| Author: | stevtec86 [ Sat Dec 24, 2011 20:29:54 ] | ||
| Post subject: | Re: Eccenter on setup sheets | ||
|
|||
| Author: | Quietman [ Sun Dec 25, 2011 01:09:16 ] |
| Post subject: | Re: Eccenter on setup sheets |
No not ecentric but eccenter standard or 1 it has on the sheets if so what would one be as below that it says diff up or down |
|
| Author: | Hagberg [ Sun Jan 01, 2012 20:37:52 ] |
| Post subject: | Re: Eccenter on setup sheets |
There are optional eccentric holders with position "1" which is higher (or lower) than standard. |
|
| Author: | Marek Gadomski [ Mon Jan 02, 2012 10:42:52 ] |
| Post subject: | Re: Eccenter on setup sheets |
| Author: | Martin Hudy [ Mon Jan 02, 2012 10:49:49 ] |
| Post subject: | Re: Eccenter on setup sheets |
yes sometimes, depends on the track conditions. When the diffs are placed down (notch up) , you get more traction, so when the traction is super low, I use 1 eccenters to get as much traction as possible. |
|
| Author: | Marek Gadomski [ Mon Jan 02, 2012 10:53:13 ] |
| Post subject: | Re: Eccenter on setup sheets |
| Author: | Stro3579 [ Wed Mar 14, 2012 05:41:18 ] |
| Post subject: | Re: Eccenter on setup sheets |
How do you change the eccenter to 1 from standard? I did not see that there is a optional new diff ring. |
|
| Author: | Fred Hubbard [ Fri Mar 16, 2012 18:12:52 ] |
| Post subject: | Re: Eccenter on setup sheets |
| Author: | zzoebl [ Tue May 26, 2015 17:33:30 ] |
| Post subject: | Re: Eccenter on setup sheets |
Is it not possible to get this for the T4? I can't seem to find them anywhere, but they are mentioned here: http://www.teamxray.com/t4/2014/ under diff height adjustment. Thank you very much. |
|
| Author: | robbie dodge [ Wed May 27, 2015 11:50:23 ] |
| Post subject: | Re: Eccenter on setup sheets |
| Author: | Migigu [ Wed May 27, 2015 13:46:01 ] |
| Post subject: | Re: Eccenter on setup sheets |
could be raised the Bulkhead!? 
|
|
| Author: | zzoebl [ Fri May 29, 2015 22:22:29 ] |
| Post subject: | Re: Eccenter on setup sheets |
I hope so, you can actually feel some difference. I'm always racing on low traction so would like to get +1 and see how it affects the car. @Migigu So how do I lower it 1mm extra? 
|
|
| Author: | Martin Hudy [ Tue Jun 02, 2015 09:01:08 ] |
| Post subject: | Re: Eccenter on setup sheets |
The +1 eccentric bushings are not available anymore as they do not fit into T4 2015. The team stopped to use them for a while as the standard eccentric bushings have the optimised position. |
|
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|