XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
T3'11 are we still drill 1mm hole on plastic shock caps? https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=10931 |
Page 1 of 1 |
Author: | Ronaldo808 [ Mon Nov 15, 2010 18:43:14 ] |
Post subject: | T3'11 are we still drill 1mm hole on plastic shock caps? |
just building my new T3 with the new bladders and lower foams is it still advisable to drill the top caps 1mm? to assist in getting zero rebounds ![]() ![]() |
Author: | neffy [ Mon Nov 22, 2010 20:56:25 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
T3-2011 should come with shock caps already drilled ![]() |
Author: | Jonny Aird [ Mon Nov 22, 2010 21:17:21 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Author: | neffy [ Sat Dec 04, 2010 20:36:54 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Yes mine are drilled right through, saved me the trouble. ![]() |
Author: | Mark Christopher [ Sun Dec 05, 2010 12:14:57 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
mine wernt! as jonny said onlty the alloy was drilled through which is the norm |
Author: | neffy [ Sun Dec 05, 2010 22:38:08 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
I looked at my Rc Disco team mates and the plastic tops are only centered with a drill hole not going right through, mine go all the way through the plastic tops. ![]() |
Author: | Ronaldo808 [ Mon Dec 06, 2010 15:01:50 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
If it didn't go right through it wouldnt do anything would it ![]() I'm drilling them now and i get just 1mm rebound with no air in the shock very happy ![]() |
Author: | Teemu Leino [ Tue Dec 07, 2010 08:23:44 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
I have been drilling mine and with new bladders shocks are very easy to build without rebound. With new bladders I dont use foam on top. I drill the hole from middle of the plastic cap all the way to the steel ball and then from the side other hole that will connect this two holes. |
Author: | Mark Christopher [ Tue Dec 07, 2010 22:11:28 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
so do you guys not use rebound now? |
Author: | Nico' [ Sun Dec 12, 2010 11:23:53 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Hi, I'm new in this forum, I have a T3 2011 and even I find it difficult to get zero rebound, I read you drill an 1mm hole on cap, can you illustrate it with a picture please because I don't hnow where on the cap to drill? |
Author: | Tricksy [ Sun Dec 12, 2010 15:43:56 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Uploaded with drill from the front diagonally down to the centre inside the cap can you make out the hole on these shocks in this pic |
Author: | xj220-sr3 [ Thu Dec 23, 2010 08:11:16 ] | ||
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? | ||
Found this drawing in the Build Manual for a different XRAY model. I can not find this picture in the T3'11 manual - and I would say it really should have been there. My only comment is that Item 6. should have said "compress the piston SLOWLY and gently".
|
Author: | Mark Christopher [ Thu Dec 23, 2010 11:02:52 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Author: | ds motorsport [ Thu Dec 23, 2010 23:12:40 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Author: | Mark Christopher [ Fri Dec 24, 2010 13:48:59 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
Author: | DarrenOakley [ Tue Jan 04, 2011 01:17:11 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
New composite shock bodys with the pre drilled cap XR308332 - COMPOSITE SHOCK PARTS - REBOUND HOLE - SHORT. Will the cap from this pack fit the Alu shocks ? or do I still need to drill mine. |
Author: | davidfricks [ Tue Jan 11, 2011 03:18:27 ] |
Post subject: | Re: T3'11 are we still drill 1mm hole on plastic shock caps? |
[quote="Teemu Leino"]I have been drilling mine and with new bladders shocks are very easy to build without rebound. With new bladders I dont use foam on top. Thanks for the tip. I had a hell of a time trying to get less than 50% with the method in the manual. I literally spent over an hour trying to get it right with no success. I'm off to buy a 1mm drill bit. Do you prefer bleeding from the top or the bottom? What percentage of Team Drivers drill their shocks? Is there a place I can see this in the setup sheet? Thank you, David F. |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |