XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
Need help with setting up GM 90 2010 speed controller https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=10694 |
Page 1 of 1 |
Author: | KevinK [ Mon Jul 26, 2010 12:27:13 ] |
Post subject: | Need help with setting up GM 90 2010 speed controller |
Hi I am a member of Mendip(Weston Supermare) which is a large out door asphalt track with a main straight of about 70 meters long and I need some help on what settings I should be using with my GM 90 2010 PRO speed controller. I am running a GM 10.5 motor and am running with standard internal gearing(1.9) and the problems I am getting is that the motor is fine for about two minutes of a five minute run (good acceleration and good top speed) them the motor seems to loose a bit of power. The motor dose seem a little warm when it comes off track after five minutes. I have tried different 64dp gear ratios and cannot get the motor to run consistently for full five minutes could anyone give any advice on what settings for speed controller and what gearing would be a good starting point to try and solve my problem. |
Author: | sidecarphil [ Mon Jul 26, 2010 22:31:29 ] |
Post subject: | Re: Need help with setting up GM 90 2010 speed controller |
Try looking on RCtech forum , there is a GM topic and Martin Hoffer is on there regularly and he will help ya |
Author: | KevinK [ Tue Jul 27, 2010 10:31:22 ] |
Post subject: | Re: Need help with setting up GM 90 2010 speed controller |
Have had a look on RCtech forum and could not find GM section is there any chance that you could post the link for the section. |
Author: | chris_dono [ Tue Jul 27, 2010 20:53:54 ] |
Post subject: | Re: Need help with setting up GM 90 2010 speed controller |
Kevin, replied to you on another forum, but send me a mail with your settings and I'll help if I can |
Author: | KevinK [ Wed Jul 28, 2010 00:36:27 ] |
Post subject: | Re: Need help with setting up GM 90 2010 speed controller |
Here is my settings at moment i have adjusted the Minimun timing from 8 to 22 as i was adviced to try. [AddData] Brushless=1 Sensor=0 Car= Place= BarCode= Comment= Motor= Pinion=0 MainGear=0 InternalGearRatio=0 TireDiameter=0 MaxRotationSpeed=48 MaxCurrent=61 [GeniusData] StartAmp=100 AmpLimit=100 Turbo=1 BrakeMin=15 BrakeMax=100 AutoBrake=0 FullBrake=100 ABS=0 RPMLimit=13 Polzahl=2 Frequency=9 Reserved=0 MaxReverse=100 Softgas=50 PowerCurve=10 Autogas=0 Switch=1 OnAfterUSB=1 Timing=0 TimingWith=2 [GeniusDataAdv] Reserved1=133 Softbrake=100 FullThrottle=22798 NeutralPoint=15359 FullBrakePoint=10065 NeutralPointWidth=80 ControllerMode=9 VoltageCutOff=250 PWMStartNoSensor=128 LimStartNoSensor=30 EffectNewBrake=150 Reserved2=8 SwitchPointRPM=63 MaxTiming=22 FixTiming=6422 Timing2=110 Timing1=110 CutOffTempContr=100 MaxRPM=48 Firmware=118 MaxCurrent=61 CutOffTempMotor=100 MaxESCTemp=60 MaxMotorTemp=49 ActESCTemp=25 ActMotorTemp=0 EEProm=9 ActVoltage=0 CurrentOffset=4 MaxTempContr=71 MaxTempMotor=92 AbsMaxCurrent=84 DisCapacity=3563 CurLimit_Temp=60 TimeToFull=175 CorrectCurLimit=64 MaxCapacity=40000 VoltageCorrect=180 MaxVoltage=155 Telemetry=131 Poles=2 Pinion=29 MainGear=110 TireDiam=63 InternGear=19 OverallGear=8879 Reserved4=3 HighByteParity=19 LowByteParity=104 |
Author: | ianp [ Wed Jul 28, 2010 22:44:47 ] |
Post subject: | Re: Need help with setting up GM 90 2010 speed controller |
http://www.rctech.net/forum/electric-ro ... hless.html its a very big section, but top info from martin.hth ianp ![]() |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |