Frans and tony.. are you criminals or something:p Tony V and Frans H :p.. Don't know how you feel about Rc racing.. but to me it's no crime
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Asphalt setup https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=8&t=1032 |
Page 1 of 8 |
| Author: | Joep [ Sun Feb 13, 2005 19:30:36 ] |
| Post subject: | Asphalt setup |
| Author: | Tonyv [ Sun Feb 13, 2005 19:37:11 ] |
| Post subject: | |
| Author: | Joep [ Sun Feb 13, 2005 19:45:30 ] |
| Post subject: | |
| Author: | Frans H [ Sun Feb 13, 2005 19:52:27 ] |
| Post subject: | |
| Author: | Rick Thomson [ Sun Feb 13, 2005 23:12:09 ] |
| Post subject: | |
Frans and tony.. are you criminals or something:p Tony V and Frans H :p.. Don't know how you feel about Rc racing.. but to me it's no crime
|
|
| Author: | Tonyv [ Sun Feb 13, 2005 23:39:11 ] |
| Post subject: | |
| Author: | Joep [ Sun Feb 13, 2005 23:50:14 ] |
| Post subject: | Does this at value to my question? |
| Author: | Frans H [ Sun Feb 13, 2005 23:59:46 ] |
| Post subject: | |
| Author: | Joep [ Mon Feb 14, 2005 08:44:22 ] |
| Post subject: | |
| Author: | Joep [ Tue Feb 15, 2005 17:56:21 ] |
| Post subject: | Droop meassurement |
| Author: | Joep [ Tue Feb 15, 2005 18:06:11 ] |
| Post subject: | Re: Droop meassurement |
| Author: | Tonyv [ Tue Feb 15, 2005 20:49:18 ] |
| Post subject: | |
The droop measurements in this setup were taken under the C-hub screw at the front and under the rear upright. Not sure where Andreas measured it, but I measure it right behind the front bumper and just to sides of the rear bumper (rear bumper is not flush with the chassis bottom...). |
|
| Author: | Joep [ Tue Feb 15, 2005 21:01:27 ] |
| Post subject: | |
thx Tony. Did it like that, but wasn't sure.... Want the weather to improve ... currently withut a job/assignment and ready for some days testing in Velp:) Was btw considiring to drive my M18 at raco but wife had ather ideas:) |
|
| Author: | Joep [ Tue Feb 15, 2005 21:03:25 ] |
| Post subject: | |
Oops lots of typo's... Working from my very small iPAQ keyboard
|
|
| Author: | new92 [ Tue Feb 15, 2005 21:37:41 ] |
| Post subject: | |
Another question on droop measurements if I may. At the rear hub I have 2 different sets of hubs. 1) has a pretty long piece where the set screw enters to hold the little hingepin and the 2nd) one has a much smaller piece. I cant remember which came with the car (T1R) as I bought a ton of extra parts when I ordered. I just noticed when I was checking the bags that some were different from others. In that case would you be better off measuring at the arm perhaps? I will get a picture tonight if someone needs for clarification. |
|
| Author: | Tonyv [ Tue Feb 15, 2005 21:41:33 ] |
| Post subject: | |
Yes, which is what some have advocated in the past. Alternatively uptravel (how far the car can be lifted before the wheel come off the ground) could be measured. Unfortunately there are many ways to measure and every driver has their own favourite way. |
|
| Author: | Joep [ Sat Feb 26, 2005 19:46:29 ] |
| Post subject: | |
| Author: | Frans H [ Sat Feb 26, 2005 21:05:27 ] |
| Post subject: | |
| Author: | Tonyv [ Sat Feb 26, 2005 21:15:29 ] |
| Post subject: | |
| Author: | Tonyv [ Sat Feb 26, 2005 21:15:55 ] |
| Post subject: | |
| Page 1 of 8 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|