| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Problem with differential https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=24&t=10636 |
Page 1 of 1 |
| Author: | Sasad [ Mon Jul 05, 2010 00:31:46 ] |
| Post subject: | Problem with differential |
Hello everyone. I have a problem with the differential. Even close up does not work, I checked several times and the assembly is correct. I had already happened once and I replaced the rear axle because it was damaged after a crash, but this time the axle is perfect. Many thanks!! Ps sorry for english... i'm italian 
|
|
| Author: | FOXY923 [ Mon Jul 05, 2010 04:23:31 ] |
| Post subject: | Re: Problem with differential |
What is the problem? Are you sure the axle is perfect? Could be the same problem? |
|
| Author: | Sasad [ Tue Jul 06, 2010 11:32:27 ] |
| Post subject: | Re: Problem with differential |
Whether differential is tight or loose I don't see difference. When the car is off the ground is ok, but when i put it on the track it doesn't give traction to the rear whells. I think that the nut that screws to tighten don't touch the washers to tighten the differential. The axle I'm almost certain that is good thanks! |
|
| Author: | FOXY923 [ Tue Jul 06, 2010 13:23:03 ] |
| Post subject: | Re: Problem with differential |
What was your previous axle problem? Sounds to me that the threaded part of the axle is coming loose from the main shaft. This would prevent the diff from getting tight no matter how much you crank on the nut. I had this happen 
|
|
| Author: | Sasad [ Wed Jul 07, 2010 19:01:51 ] |
| Post subject: | Re: Problem with differential |
I solved the problem with add other 2 shim and now when i tight the differential works well. But what's the real problem?? Considering that I changed all the bearings and washers and doesn't resolve. |
|
| Author: | Sasad [ Mon Jul 12, 2010 00:55:37 ] |
| Post subject: | Re: Problem with differential |
Unfortunately I hadn't solved the problem. After less than a minute the differential is loosened again and the car sled. Any advice? |
|
| Author: | FOXY923 [ Mon Jul 12, 2010 16:55:34 ] |
| Post subject: | Re: Problem with differential |
I still think it's the axle. Even if it looks ok it may not be. Without being able to see the problem it's hard to determine. Maybe try a new nut. The nylon could be worn out. |
|
| Author: | dergeorg [ Mon Jul 12, 2010 21:52:08 ] |
| Post subject: | Re: Problem with differential |
I think that this is the same problem as i had!!! The screw that is in the axle has got a little bit out of the axle and so it is damaged and the nut can´t get the diff tight!If that is the problem then you can´t repair it! I tried everything! I think that it tightend the nut too much so i pulled the screw outside! |
|
| Author: | FOXY923 [ Mon Jul 12, 2010 21:54:46 ] |
| Post subject: | Re: Problem with differential |
| Author: | dergeorg [ Tue Jul 13, 2010 19:36:17 ] |
| Post subject: | Re: Problem with differential |
I had 2 axle´s with this problem!! And i wrote this to Xray and the said that the don´t know any problem about that! |
|
| Author: | Sasad [ Thu Jul 15, 2010 23:27:05 ] |
| Post subject: | Re: Problem with differential |
Virtually all have the same problem. Anyone know if we can adapt the solid axle of another brand? |
|
| Author: | FOXY923 [ Fri Jul 16, 2010 01:47:10 ] |
| Post subject: | Re: Problem with differential |
| Author: | ElliotCanada [ Sat Jul 17, 2010 03:38:26 ] |
| Post subject: | Re: Problem with differential |
I've had an Associated Axle do this as well. Simple solution - don't over tighten the diff. 
|
|
| Author: | yong-i7 [ Wed Sep 15, 2010 09:12:13 ] |
| Post subject: | Re: Problem with differential |
wELL!!This is what the problem that was in my mind. Sounds just like what happened on my X10 (same axle for both cars) Xray, is this an issue that should be looked at? God Bless!!!!! |
|
| Author: | Tekinmaster [ Tue Nov 02, 2010 23:33:26 ] |
| Post subject: | Re: Problem with differential |
hey at all, hey sasad, please check, if it is possible that you can pull down all bearings from the differential. after crash it could possible, that the screw in the carbon axle expand the axle and it is not possible to pull down the bearings. If it is extreme, you are not able to tighten the diff correctly,because the wheel hub can´t jump over this hump. I do not have such problems....... I can´t believe that you have this problems on a NEW axle without crashes  best regards Harald and greetings from vienna |
|
| Author: | Anders Lind [ Wed Nov 24, 2010 12:19:09 ] |
| Post subject: | Re: Problem with differential |
Hi, I had the same problem yesterday when I was out and train. You make it about 1000 times but thought it will be bad. In my case it was threaded piece which spans diffet. Twist the threaded piece out and glue it back in again. Then I had no problem. Hope you understand my English. Uses Google Translate. : O) Greetings Anders Lind |
|
| Author: | FOXY923 [ Wed Nov 24, 2010 15:49:53 ] |
| Post subject: | Re: Problem with differential |
| Author: | Sasad [ Mon Nov 29, 2010 23:21:18 ] |
| Post subject: | Re: Problem with differential |
Yes the problem is always the same. But now with new axle at the moment I hadn't problem. I hope to continue 
|
|
| Author: | Mark_Wallin [ Fri Jun 24, 2011 08:51:07 ] |
| Post subject: | Re: Problem with differential |
It does sound like the screw is working its way out of the carbon, XRAY have released an allow Axel that should fix this. One thing though, is the clamp for the wheel adapter at the other end tight? Its possible if this is lose for the axel to spin and feel like diff slip? |
|
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|