| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| Novarossi 353 and clutch setup https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=21&t=9310 |
Page 1 of 1 |
| Author: | Dimitris P. [ Tue Jun 02, 2009 20:26:06 ] |
| Post subject: | Novarossi 353 and clutch setup |
Hello, I tried to install the clutch on the 353 09 engine, using the short of the 2 cones that come with the engine. The longer cone gives even worst results. The problem is that the distance from the top of the flywheel nut until the end of the crankshaft is only 9.0 and there is not much space left to achieve clutch gap 0.6 or 0.7. The maximum clutch gap I can achieve is 0.4. What do you recommend? Thanks in advance Dimitris |
|
| Author: | musti72 [ Tue Jun 02, 2009 20:51:42 ] |
| Post subject: | |
This was talked some time time ago, the solution: put some shims in front of the crankshaft, between bushing and crankshaft, so you lenghten the crankshaft, did you understand what I mean? |
|
| Author: | Dimitris P. [ Tue Jun 02, 2009 21:00:33 ] |
| Post subject: | |
Yes, I got it. You mean the 3x5 shims. Thanks |
|
| Author: | Roelof [ Tue Jun 02, 2009 21:39:16 ] |
| Post subject: | |
If there is some space between the flywheel and the engine front bearing you can always grind off some material of the conus to find some tenths of a mm. |
|
| Author: | Dimitris P. [ Wed Jun 03, 2009 10:17:52 ] |
| Post subject: | |
| Author: | Roelof [ Wed Jun 03, 2009 13:42:25 ] |
| Post subject: | |
O no, that is not needed. The working of the clamp on the shaft will not be affected, so the flywheel will still be mounted straight. Just use some sandpaper on a flat surface and rubb the conus over it. |
|
| Author: | Dimitris P. [ Fri Jun 05, 2009 09:58:31 ] |
| Post subject: | |
| Author: | Zapalot [ Wed Apr 07, 2010 12:27:23 ] |
| Post subject: | Halp |
| Author: | Dimitris P. [ Wed Apr 07, 2010 13:44:31 ] |
| Post subject: | |
| Author: | Zapalot [ Wed Apr 07, 2010 14:48:32 ] |
| Post subject: | |
Hello, thanks for the fast reply, im not at home right now but did some picture work for the people wondering too. I hope this is was u ment. Many thanks for the help 
Greets Florian Edit: I didnt used the shims(aint got them), i just used the bushing from my Mugen 1/8 Clutch, seems to work out just perfect. Nice clutch gap and ultra nice clutch endplay
|
|
| Author: | Dimitris P. [ Thu Apr 08, 2010 23:10:10 ] |
| Post subject: | |
| Author: | rx7ttlm [ Sat Apr 10, 2010 02:13:47 ] |
| Post subject: | Re: Novarossi 353 and clutch setup |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|