| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| anyone tryed 338512 - NT1 Optional Alu Clutch Bell https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=21&t=8241 |
Page 1 of 2 |
| Author: | grub [ Sun Sep 14, 2008 11:11:06 ] |
| Post subject: | anyone tryed 338512 - NT1 Optional Alu Clutch Bell |
| Author: | TP222 [ Mon Sep 15, 2008 18:15:00 ] |
| Post subject: | Re: anyone tryed 338512 - NT1 Optional Alu Clutch Bell |
| Author: | Delboy [ Tue Sep 16, 2008 10:57:45 ] |
| Post subject: | |
| Author: | TP222 [ Tue Sep 16, 2008 18:28:52 ] |
| Post subject: | |
| Author: | Delboy [ Tue Sep 16, 2008 18:59:57 ] |
| Post subject: | |
| Author: | rx7ttlm [ Tue Nov 11, 2008 08:45:51 ] |
| Post subject: | light weight flywheel |
| Author: | Delboy [ Tue Nov 11, 2008 09:10:11 ] |
| Post subject: | |
| Author: | grub [ Tue Nov 11, 2008 09:24:55 ] |
| Post subject: | |
| Author: | Laoma [ Wed Nov 12, 2008 15:43:32 ] |
| Post subject: | |
| Author: | Delboy [ Wed Nov 12, 2008 21:46:57 ] |
| Post subject: | |
Loama A photograph would be appreciated! That is unbelievable. Maybe the bell distorts when it gets hot as the coefficient of expansion of aluminium is much higher than steel. (which is the reason why we heat the engine in the oven to remove the steel bearing easily). There is something not quite right here. The top drivers at our club has fitted an alu bell so I will be watching with interest to see how he gets on. I will let the forum know. We will be using a steel bell as I have grave reservations about the alu bell. |
|
| Author: | rcfoolz [ Thu Nov 13, 2008 10:48:38 ] |
| Post subject: | |
If ran the aluminum bell 2 times. Both for qualifier runs. Seems to me that a harder clutch shoe would be better when using it, as it did have more wear on the yellow shoe than I would have expected |
|
| Author: | Laoma [ Thu Nov 13, 2008 14:59:26 ] |
| Post subject: | |
Image of the cracked bell. If picture doesn't appear, just go to the link above. |
|
| Author: | Delboy [ Thu Nov 13, 2008 16:21:12 ] |
| Post subject: | |
Thanks for the photographs. The fact that the bell broke near the hole, which is obviously the weakest part of the component, could indicate that it simply exploded. Because of the position of the bell it is unlikely to get damaged as it's protected by the gearing/flywheel. Strange???? |
|
| Author: | rcfoolz [ Thu Nov 13, 2008 19:11:30 ] |
| Post subject: | |
| Author: | Delboy [ Thu Nov 13, 2008 20:43:18 ] |
| Post subject: | |
| Author: | TP222 [ Fri Nov 14, 2008 10:16:45 ] |
| Post subject: | |
| Author: | rcfoolz [ Sat Nov 15, 2008 15:27:25 ] |
| Post subject: | |
| Author: | Delboy [ Sat Nov 15, 2008 22:31:32 ] |
| Post subject: | |
| Author: | rx7ttlm [ Mon Nov 17, 2008 02:05:58 ] |
| Post subject: | al clutch bell |
| Author: | rcfoolz [ Mon Nov 17, 2008 03:48:37 ] |
| Post subject: | |
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|