WOW!! what a powerful P-0, man!! Seem like the car can hardly control when you full throttle on the sand. I believe once you do the convertion to the MT, it's more in control. Great engine!! cheers!!
| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| NT18T With Picco p-0 https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=18&t=4326 |
Page 1 of 1 |
| Author: | phatmonkey [ Mon Oct 09, 2006 01:33:25 ] |
| Post subject: | NT18T With Picco p-0 |
Check this video out it was made today in my backyard http://www.youtube.com/watch?v=Zep87QaadWM be warned that if you drive in grass it will overwork the diffs I had to tighten them 3/4 turns after this run today. |
|
| Author: | geezatec [ Mon Oct 09, 2006 03:19:06 ] |
| Post subject: | |
Kewl! Vid!! monkey!! The on the grass thing, more resistance on grass then concrete. I'd work on the idle lower. and the clutch shoe to engage sooner. So loosin the spring. you'll be more happier whan you do. lol! I installed the P-Zero on my NT18 last night. was goin to break in today. Have to wait. The Clutchbell has too much endplay that it has a bell sound in it. Had to order them. |
|
| Author: | evo165 [ Mon Oct 09, 2006 12:38:21 ] |
| Post subject: | |
WOW!! what a powerful P-0, man!! Seem like the car can hardly control when you full throttle on the sand. I believe once you do the convertion to the MT, it's more in control. Great engine!! cheers!!
|
|
| Author: | Mark Harris [ Mon Oct 09, 2006 15:19:33 ] |
| Post subject: | |
damn nice mate! Hope you have the alloy drive shafts in that! |
|
| Author: | phatmonkey [ Mon Oct 09, 2006 17:18:40 ] |
| Post subject: | MT convert |
Yea the mt setup does add ride height and more clearance.And the Picco P-0 is too powerful to run at full throtlle on a sandy surfaces.With 30% fuel its running 3&3/5 turns out on the highspeed needle and runs medium hot plus the higher nitro content makes this truck scream. 
|
|
| Author: | vick [ Mon Oct 09, 2006 18:57:45 ] |
| Post subject: | Re: NT18T With Picco p-0 |
| Author: | phatmonkey [ Mon Oct 09, 2006 19:13:37 ] |
| Post subject: | no leaks |
| Author: | vick [ Mon Oct 09, 2006 20:00:39 ] |
| Post subject: | Re: no leaks |
| Author: | evo165 [ Tue Oct 10, 2006 13:17:59 ] |
| Post subject: | |
Hi vick, here are the link of the required mod needed to be done in order to fit the P-0 engine in. viewtopic.php?t=4170 If you still have problem, you can either pm me or phatmonkey. I bought the P-0 engine from Towerhobbies. http://www2.towerhobbies.com/cgi-bin/wt ... LXNAE5&P=7 There are some link in the forum that is slightly cheaper than towerhobbies price. Do search around.
|
|
| Author: | Mark Harris [ Tue Oct 10, 2006 13:57:22 ] |
| Post subject: | |
Tower $155 KillerHobbies.com $139 http://www.killerhobbies.com/Browse_Ite ... -_OFN51118 |
|
| Author: | evo165 [ Tue Oct 10, 2006 18:43:13 ] |
| Post subject: | |
| Author: | geezatec [ Tue Oct 10, 2006 18:47:03 ] |
| Post subject: | |
| Author: | vick [ Tue Oct 10, 2006 19:39:44 ] |
| Post subject: | |
| Author: | Mark Harris [ Wed Oct 11, 2006 01:23:38 ] |
| Post subject: | |
| Author: | geezatec [ Wed Oct 11, 2006 02:29:50 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|