| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| M18 Pro with side motion https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=11&t=8520 |
Page 1 of 2 |
| Author: | schumo99 [ Wed Dec 03, 2008 14:44:09 ] |
| Post subject: | M18 Pro with side motion |
| Author: | Robin Frischkopf [ Wed Dec 03, 2008 16:04:45 ] |
| Post subject: | |
| Author: | Tekinmaster [ Wed Dec 03, 2008 19:13:01 ] |
| Post subject: | |
| Author: | Mini_Me [ Thu Dec 04, 2008 00:25:28 ] |
| Post subject: | |
| Author: | geezatec [ Fri Dec 05, 2008 06:21:50 ] |
| Post subject: | |
Give more info. Linkage of steering not binding, What diff you're useing, gear or ball. What are your toe-in/out frt & rear, Servo finding home at neutral? |
|
| Author: | schumo99 [ Fri Dec 05, 2008 14:47:51 ] |
| Post subject: | |
| Author: | Mini_Me [ Fri Dec 05, 2008 15:21:02 ] |
| Post subject: | |
| Author: | geezatec [ Sat Dec 06, 2008 03:29:54 ] |
| Post subject: | |
| Author: | Alex73 [ Wed Dec 17, 2008 18:20:47 ] |
| Post subject: | |
I am having the same problem with mine. It seems to be going straight, then i steer and it goes off to one side, then sometimes off to the other side. Happens with new and old tires. m18t pro is very new. It does make it very hard to drive at speed. |
|
| Author: | Mini_Me [ Thu Dec 18, 2008 00:24:53 ] |
| Post subject: | |
That might be your servo. What servo are you using on it? Some can loose their center and start drifting. |
|
| Author: | Alex73 [ Thu Dec 18, 2008 22:49:52 ] |
| Post subject: | |
| Author: | Mini_Me [ Fri Dec 19, 2008 00:09:13 ] |
| Post subject: | |
| Author: | iPearl [ Fri Dec 19, 2008 00:09:37 ] |
| Post subject: | |
| Author: | Alex73 [ Tue Dec 23, 2008 23:32:14 ] |
| Post subject: | |
Ok, I have run the bats down then decided to try to sort out this steering problem. Things i changed/want to change: 1) The front ball diff was a little looser than the back so i have tightened the front so it is tighter. (how tight should it be? i can spin the wheel by holding the gear and one wheel but its quite tight) 2)I have changed the toe, on the rear, i have lowered it and matched it up better (one side was a bit more than other). 3) The front has a little toe (other direction though), but very little. 4) The front wheels tip down a little but this can't be adjusted, is this ok? 5) I am thinking of getting a decent servo for this, so what is a good digital servo? I want something very reliable and good quality. I am going to get a 2-cell lipo for this and can't wait. Any you can recommend? Sorry for taking over the thread a bit. Thanks for all the help guys |
|
| Author: | Alex73 [ Thu Dec 25, 2008 23:25:13 ] |
| Post subject: | |
I have run it since these changes and its a lot better. Still goes off to one or the other side, so will try a new servo. Which one? Happy xmas |
|
| Author: | iPearl [ Fri Dec 26, 2008 05:20:59 ] |
| Post subject: | |
| Author: | Alex73 [ Fri Dec 26, 2008 13:58:12 ] |
| Post subject: | |
| Author: | Alex73 [ Fri Dec 26, 2008 20:39:37 ] |
| Post subject: | |
| Author: | geezatec [ Sat Dec 27, 2008 19:52:15 ] |
| Post subject: | |
| Author: | Alex73 [ Sat Dec 27, 2008 20:15:48 ] |
| Post subject: | |
| Page 1 of 2 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|