XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
X-Ray M18 Adj. Turnbuckle problem https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=11&t=4643 |
Page 1 of 1 |
Author: | Orfeous [ Sun Dec 10, 2006 12:08:48 ] |
Post subject: | X-Ray M18 Adj. Turnbuckle problem |
Author: | JC Borcy [ Sun Dec 10, 2006 13:50:07 ] |
Post subject: | Re: X-Ray M18 Adj. Turnbuckle problem |
Author: | Orfeous [ Sun Dec 10, 2006 13:58:25 ] |
Post subject: | |
Author: | kant76 [ Sun Dec 10, 2006 18:10:23 ] |
Post subject: | |
Author: | Orfeous [ Sun Dec 10, 2006 18:17:03 ] |
Post subject: | |
Author: | kant76 [ Sun Dec 10, 2006 18:55:14 ] |
Post subject: | |
Author: | Orfeous [ Sun Dec 10, 2006 19:04:41 ] |
Post subject: | |
Author: | kant76 [ Sun Dec 10, 2006 20:33:23 ] |
Post subject: | |
Author: | Orfeous [ Sun Dec 10, 2006 20:42:29 ] |
Post subject: | |
Author: | kant76 [ Mon Dec 11, 2006 02:47:36 ] |
Post subject: | |
Author: | Orfeous [ Tue Dec 12, 2006 00:12:05 ] |
Post subject: | |
Author: | Orfeous [ Tue Dec 12, 2006 15:16:36 ] |
Post subject: | |
How do i measure the toe-in with my new turnbuckles? i want 2.5 degree rear.. how long should the turnbuckles be or how can i measure the angle of rear tires? |
Author: | Mini_Me [ Tue Dec 12, 2006 15:39:19 ] |
Post subject: | |
Author: | Orfeous [ Tue Dec 12, 2006 15:50:27 ] |
Post subject: | |
i have allready checked it and the lengths isnt the same as in real life.. please measure the 4 degree turnbuckles so i can set my turnbuckles in that length |
Author: | kant76 [ Wed Dec 13, 2006 02:07:26 ] |
Post subject: | |
mini me that fault in the instructions are exatly the ones you have linked to, those values are totaly off on that sheet, if you try mesure as shown ! |
Author: | Mini_Me [ Wed Dec 13, 2006 04:33:39 ] |
Post subject: | |
Kant or Orfeous, could you do me a favor and try 0 degree length? Then tell me if your getting toe in or out. If your getting toe in with what should be a 0 degree.. do me a favor. Try the measurement listed from the mid point of the pivot ball versus the outer ends. |
Author: | Orfeous [ Wed Dec 13, 2006 12:03:25 ] |
Post subject: | |
maybe kant76 can do... ![]() |
Author: | kant76 [ Wed Dec 13, 2006 12:03:42 ] |
Post subject: | |
i´ll will do that and pm you asap. ok |
Author: | Orfeous [ Wed Dec 13, 2006 12:09:03 ] |
Post subject: | |
why cant you just write the results here? ![]() i am curious ![]() |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |