| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| lipos!! https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=11&t=3839 |
Page 1 of 1 |
| Author: | rex222 [ Sat Jul 01, 2006 04:24:39 ] |
| Post subject: | lipos!! |
| Author: | Mini_Me [ Sat Jul 01, 2006 10:15:47 ] |
| Post subject: | |
| Author: | Rc_boy [ Sun Jul 02, 2006 08:04:32 ] |
| Post subject: | |
| Author: | Mini_Me [ Sun Jul 02, 2006 11:39:22 ] |
| Post subject: | |
It all a matter of personal preference. If your running the stock chassis, you might dremel or cut of the interior outside buttresses *NOT THE TUB/WALL on the battery side. They usually help retain regular nimh batteries. By removing them you dont weaken the chassis, and it allows more room (about 34" in width) to fit a lipo. For even more room and pack options, look at purchasing the Now personally, I use Thunder Power 1320mah packs. But that works best for my usage. WIth a monster truck you probably will want to look at a higher mah and "C" rating with the higher amp draw. |
|
| Author: | rex222 [ Sun Jul 02, 2006 14:41:50 ] |
| Post subject: | |
i have the m18T truck. i have also bought the graphite chassis for it which comes with the 6 cell holder. |
|
| Author: | rex222 [ Sun Jul 02, 2006 14:49:36 ] |
| Post subject: | |
whats the most powerful battery u could fit in there? i will be buying the tekin brushless 6.8 system soon so i want a good powerful li-po with great runtimes |
|
| Author: | bbking9 [ Tue Jul 04, 2006 21:33:10 ] |
| Post subject: | |
| Author: | rex222 [ Wed Jul 05, 2006 09:18:35 ] |
| Post subject: | |
| Author: | rex222 [ Wed Jul 05, 2006 09:21:56 ] |
| Post subject: | |
| Author: | rex222 [ Wed Jul 05, 2006 09:32:36 ] |
| Post subject: | |
| Author: | Mini_Me [ Wed Jul 05, 2006 16:34:35 ] |
| Post subject: | |
| Author: | Peter Szuhai [ Thu Aug 03, 2006 17:31:38 ] |
| Post subject: | |
| Author: | Mini_Me [ Thu Aug 03, 2006 21:35:04 ] |
| Post subject: | |
| Author: | Peter Szuhai [ Sat Aug 05, 2006 06:12:43 ] |
| Post subject: | |
http://pfmdistribution.com/secure/shop/ ... 3&catid=38 This one is only 31.1Wide that should fit right? |
|
| Author: | Mini_Me [ Sat Aug 05, 2006 15:42:21 ] |
| Post subject: | |
Not sure with that length. I would contact them first to check. I can tell you that you would need the Edit: They say it fits.. but again Im assuming they mean with the above since the stock battery retainer is only listed for a stick pack which I believe is under 100mm. Also "Slightly thicker than standard Ni-Cd/Mh round cells due to cell spacers. May have to shim battery stud on chassis." Doing that with the above will possibly interfere with the bellcrank. Look at the 2 cell version instead or again contact them to see what their test system setup is using. (case in point 24.1mm Thick right? A 2/3A is under 18mm!!) |
|
| Author: | Duster_360 [ Fri Aug 18, 2006 03:15:20 ] |
| Post subject: | |
| Author: | 4ever [ Sat Aug 19, 2006 17:02:01 ] |
| Post subject: | |
| Page 1 of 1 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|