XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
m18t springs https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=11&t=2608 |
Page 1 of 1 |
Author: | minimad [ Fri Nov 18, 2005 10:48:20 ] |
Post subject: | m18t springs |
Author: | LugNutz [ Fri Nov 18, 2005 21:12:13 ] |
Post subject: | |
Author: | minimad [ Sat Nov 19, 2005 01:38:30 ] |
Post subject: | |
thanks, ill track some down. |
Author: | k_bojar [ Mon Nov 21, 2005 18:09:07 ] |
Post subject: | |
Author: | minimad [ Sat Nov 26, 2005 15:44:18 ] |
Post subject: | |
Author: | lextek [ Sun Nov 27, 2005 00:32:15 ] |
Post subject: | |
Author: | minimad [ Sun Nov 27, 2005 01:17:42 ] |
Post subject: | |
Author: | lextek [ Sun Nov 27, 2005 02:51:39 ] |
Post subject: | |
The Mini Quake fit fine front and rear no mods. I was going to try the Mini-T springs with the RC18T retainers. http://www2.towerhobbies.com/cgi-bin/wt ... LXJKV7&P=K I was having better results with my RC18T, but there is too, much potential here. Two qualifiers two trucks. |
Author: | lextek [ Sun Nov 27, 2005 02:53:51 ] |
Post subject: | |
As far as a graphite chassis. I asked Motek if they were going to do a kit for the M18T like the M18. They said they didn't think it needed it. I agree the stock chassis ivery. rigid. But. Cf is always cool. |
Author: | minimad [ Sun Nov 27, 2005 03:36:01 ] |
Post subject: | |
just put mini t springs on, seems better but i'll let you know after a race tomorrow. the mini t springs are a little large but seem to work ok. i had to put rear springs on the front too. i put blues on the back and silvers on the front. no rc18t clip needed. |
Author: | minimad [ Sun Nov 27, 2005 03:36:57 ] |
Post subject: | |
i dont buy from tower as they dont paypal. |
Author: | lextek [ Sun Nov 27, 2005 18:02:46 ] |
Post subject: | |
Author: | minimad [ Mon Nov 28, 2005 09:04:56 ] |
Post subject: | |
cool, thanks for that, do u think they are better than mini t springs? |
Author: | oXYnary [ Mon Nov 28, 2005 09:31:59 ] |
Post subject: | |
Just a FYI for everyone, please don't link external sites to other companies products. If you want to show someone, please PM them. Thanks. |
Author: | ttppll [ Wed Dec 07, 2005 16:45:53 ] |
Post subject: | |
Author: | lextek [ Thu Dec 08, 2005 04:10:18 ] |
Post subject: | |
Author: | ttppll [ Thu Dec 08, 2005 16:43:24 ] |
Post subject: | |
Author: | lextek [ Thu Dec 08, 2005 20:50:38 ] |
Post subject: | |
Author: | ttppll [ Thu Dec 08, 2005 22:12:35 ] |
Post subject: | |
Page 1 of 1 | All times are UTC + 2 hours |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |