| XRAY - Model racing cars https://setup.teamxray.com/xsetup/legacy/ |
|
| XRAY M18 General Forum https://setup.teamxray.com/xsetup/legacy/viewtopic.php?f=11&t=16 |
Page 4 of 5 |
| Author: | Mini_Me [ Sat Dec 01, 2007 23:33:04 ] |
| Post subject: | |
| Author: | kptkyle [ Sun Dec 02, 2007 17:13:06 ] |
| Post subject: | |
| Author: | Mini_Me [ Mon Dec 03, 2007 04:19:29 ] |
| Post subject: | |
| Author: | kptkyle [ Thu Dec 06, 2007 04:55:48 ] |
| Post subject: | |
| Author: | Acid [ Thu Dec 06, 2007 21:13:58 ] |
| Post subject: | |
1) its ok 2) load the car vith equipment and put it on something flat, i think problem will disapear.. you can also screw downnstops a little bit |
|
| Author: | Mini_Me [ Fri Dec 07, 2007 02:03:20 ] |
| Post subject: | |
| Author: | kptkyle [ Fri Dec 07, 2007 03:51:54 ] |
| Post subject: | |
| Author: | Mini_Me [ Fri Dec 07, 2007 05:33:00 ] |
| Post subject: | |
| Author: | kptkyle [ Fri Dec 07, 2007 13:44:22 ] |
| Post subject: | |
| Author: | jRay91 [ Mon Dec 10, 2007 00:00:57 ] |
| Post subject: | Xray M18 RTR ? |
| Author: | kptkyle [ Mon Dec 17, 2007 03:55:57 ] |
| Post subject: | |
| Author: | Mini_Me [ Mon Dec 17, 2007 04:10:43 ] |
| Post subject: | |
| Author: | kptkyle [ Mon Dec 17, 2007 13:44:28 ] |
| Post subject: | |
| Author: | Mini_Me [ Mon Dec 17, 2007 14:37:43 ] |
| Post subject: | |
| Author: | kptkyle [ Mon Dec 17, 2007 23:34:49 ] |
| Post subject: | |
| Author: | Mini_Me [ Tue Dec 18, 2007 05:37:50 ] |
| Post subject: | |
| Author: | kptkyle [ Tue Dec 18, 2007 14:09:19 ] |
| Post subject: | |
| Author: | greatestkelvin [ Tue Feb 05, 2008 07:09:16 ] |
| Post subject: | I have a question |
| Author: | Mini_Me [ Tue Feb 05, 2008 11:31:47 ] |
| Post subject: | |
Roelof already answered you in the other thread, but you have one of the differentials in backwards. |
|
| Author: | CM.ENT [ Mon Apr 07, 2008 22:54:18 ] |
| Post subject: | Rough diff |
Hi everyone, I just received my M18 PRo in the mail and started building the diffs. I have one question. They seem a little rough in a couple spots when I turn them (both front and rear). I noticed some folks add grease or oil, but it looks like Xray recommends running them dry, so that's what I did. The main gear that the driveshaft attaches to is smooth when turned by itself, and the small gear that transfers power to the front and back is smooth turning as well. When I put them together there is just a couple of spots that I feel some resistance from. I have taken both apart and looked under a light, flashlight, etc... and can't find any kind of burr on the gears. Any ideas? Thanks, Mark |
|
| Page 4 of 5 | All times are UTC + 2 hours |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|